Autopot Air Dome - Free 3D Print Model

Search models, users, collections, and posts

Clucky

Household>Garden

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 3 walls, 25% infill

Designer

4 h

1 plate

4.6(19)

Open in Bambu Studio

Boost

177

380

204

Released

Description

This is the air dome for the autopot system. Same size as the original and prints with minimal supports. This design has holes in the middle of the + air bubbler to replace the blue hoses that autopot sells. Hook an air pump up to it and it blows more bubbles than an airstone. Use this with the autopot air base: https://makerworld.com/en/models/56624#profileId-58263

Comment & Rating (33)

@Spenny

Boosted

Print Profile

0.2mm layer, 3 walls, 25% infill

Bottom left plant I this printed airdome and it seems to be growing better than the rest of the original airdomes! 🥳 Thanks for sharing and greetings from South Africa 🙏

@2asd1asd

Really,.. did you noticed a differents in weight after harvesting?

@Spenny

Boosted

Replying to @2asd1asd :

these were all different strains so the yield was very different throughout. im using them again for my next run of mostly Ethos

@kurt_sichtig

Printed without supports due to comments. As a result, the connection for the hose is not perfectly round. However, it still works. I made the connection round inside with a drill

Show original

@user_1716635319

Sits flush after inserting.

@hweckman

Print Profile

0.2mm layer, 3 walls, 25% infill

Great work👍😉

@user_1456467910

Print Profile

0.2mm layer, 3 walls, 25% infill

came out great. saw a previous post about support issues so I printed this without any. had some stringing near the top on the underside because of it but it does nothing to the function. printed in generic petg and I show it with an airbase model I got from here as well. going to test how well the air function works but I don't mind running an airstone if not as good. still a great print and great to have an extra on hand

@bamb_ushu

Boosted

Print Profile

0.2mm layer, 3 walls, 25% infill

great print in ABS, I already made a few of them and they work great.

@user_1209612344

@SenorMichael , please think before you write, this is an STL file, where you place any support is your business and your slicer's, the file itself is absolutely fine. If support is placed in the wrong places, it is due to your inability to operate your slicer. To rate it poorly because of that is truly more than unfair

Show original

@FormaDelSol

Thank you for your feedback However there is a fundamental misunderstanding here that I would like to clarify As mentioned in my review I did not download the STL file but rather the 3MF file from MakerWorld Unlike a plain STL file which only contains the 3D model a 3MF file includes a complete print profile with all slicer settings The support structures and other parameters I criticized were therefore explicitly configured by you in the file It therefore has nothing to do with 'my inability to operate the slicer' I deliberately relied on the profile you provided – that is precisely the purpose of a ready-made 3MF profile on MakerWorld If this profile is flawed then my review refers to this deficient overall package The review is therefore absolutely justified

Show original

@FormaDelSol

Print Profile

0.2mm layer, 3 walls, 25% infill

Support Issue:It works, but AFTER I printed it, I wondered why so less air is coming out. I checked the slicer and found the support inside the pipes. For a print ready file this is very anoying, also i would design it different to print it better.

@mkvsn

Boosted

Print Profile

0.2mm layer, 3 walls, 25% infill

The airdome is slightly smaller or lower than the hole in the base, but this can be adjusted by pressing it into the hole in the base and carefully placing the substrate over it. Otherwise the model makes a very good impression, thank you very much!

The profile uploader has replied

@Cluckn

The OEM air domes are the exact same size. You must have never used a real one to compare them.

@Italianrelic

Print Profile

0.2mm layer, 3 walls, 25% infill

it’s so so, air sucks coming out of it

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.