P1S / X1C Poop Chute (Right side / Opposite Side) - Free 3D Print Model

Search models, users, collections, and posts

Stu Fisher

3D Printer>3D Printer Parts

IP Report

Print Profile(2)

All

P1S

P1P

X1E

H2D Pro

X1 Carbon

H2D

H2S

H2C

P2S

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

3.7 h

1 plate

4.1(13)

Fixed Screw Position, Enabled Support, New Larger Bucket

4.6 h

2 plates

5.0(7)

Open in Bambu Studio

Boost

208

248

152

Released

Description

PRINT WITH SUPPORT
the slicer will tell you to…

But you should be smart enough to figure it out

I wanted to make life Much more difficult for myself, so I put my Poop Chute on the Right Hand Side.

I also made a (VERY SMALL) Poop Bucket.

But The PoopChute does ok.

The Bottom Screw Hole is a bit off… .so it will really need to be moved if you want to use it. But my PoopChute rests on the power cord just fine.

I just like saying Poopchute

Poop!

Comment & Rating (33)

@SunnyboyRides

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

FINALLY! A chute for the right side. the hole placement is wrong as announced. but as also announced it holds fine against the power cable. I dont like that i feel like ripping out the thread on the one bolt that does all the carrying now, when accidentally touching it. Gotta be careful! apart from the misaglined screw hole, everything is good.

@user_3420418380

Boosted

ikr

@user_3420418380

Boosted

Replying to @user_3420418380 :

the right side!!!

@Albey

Print Profile

0.2mm layer, 2 walls, 15% infill

Support Issue:not sure why this printed without supports. but it definitely needed supports. great design and idea. would love to see this with the screw hole aligned properly, supports added, and chute going all the way to the edge of the machine.

The profile uploader has replied

@stuart_fisher

I do say to print it with support. But you're right I really should do what I can to fix it.

@PessyTV

Hello what is that holder for the cables in the back

The designer has replied

Show original

@stuart_fisher

I found it in the Maker Space but I searched for a long time and cannot find it again I am very sorry

Show original

@LordLancifer

search Cable Tidy https://makerworld.com/models/142877?appSharePlatform=copy

@don.fief

Does this work with an X1C? I don't know how it compares with the P1

@don.fief

Turns out, yes it does...

@TheHit4Hire

Print Profile

Fixed Screw Position, Enabled Support, New Larger Bucket

Printed great first try and a great fit. Exactly what I was looking for.

@Irlandus

I know that this is just a poop chute but its realy bad- no supports (why?) leding to massive overhangs... I've stop this mess in 80-90% finish and tossed it to the trash...

The designer has replied

@stuart_fisher

In the Print profile... I did say to print with supports... And given your obvious superior intellect, I guess you could have made the decision to Print it with supports all on your own. Having said that.. .I designed it.. printed it (with supports) It works for me, and I uploaded it. You wanna change it, and do better, Have at it.

@ZAPPY76

Print Profile

Fixed Screw Position, Enabled Support, New Larger Bucket

Very useful while waiting for enough filament to move on to the ultimate version of the poop drawer catcher.

Show original

@daFexKM

The general design is very nice! Just one improvement would be to be able to print it without support (or much less). This would be possible with a beveled edge, where the screws are. Or only have the overhang where the screws really are to reduce the support a lot.