Track square for Festool, Bosch and Makita tracks - Free 3D Print Model

Search models, users, collections, and posts

LF Prints

Tools>Gadgets

IP Report

Print Profile(1)

All

H2D Pro

H2D

X1 Carbon

P1P

P2S

P1S

H2C

X1E

H2S

X2D

A2L

0.2mm layer, 3 walls, 15% infill

2.8 h

1 plate

4.5(18)

Open in Bambu Studio

Boost

151

561

516

297

Released

Description

track square for most track saws, is 225mm x210mm fits on a 210mm bed going diagonal.

printed on a Prusa MK3s and a Bambu lab P1s at .2 layer height

Comment & Rating (48)

@BCMTech

Print Profile

0.2mm layer, 3 walls, 15% infill

Print quality was fine, however when installed in Makita Tracks, it leaves a bit of slop and is not a tight enough tolerance. As a result, you must make sure you are pushing the square towards the track to get a true 90 degree angle.

@user_3560681765

just updated

@dancika_94

Replying to @user_3560681765 :

is the current version the last version that should be fitting on makita tracks?

@user_3560681765

Replying to @dancika_94 :

it should fit on makita tracks with a tight friction fit so it shouldnt move at all

@MogensEngmark

Printet this one af I had a project where this would be handy. Overall it looked nice. Fitting was quite easy and I think it fitted well to my Festool FS1400 track. I checked for square and it looked very nice. After a few cuts I measured for square again - it seems fine, but the track did not quite align with my measurements on the subject I was cutting. I then noticed that the printed square had room for a little wiggle, not much, but enough to be in 90 degrees when the cut was 60 cm long or so. I am considering if adding small bolt or two underneath will apply enough pressure towards the the track, securing it or be square.

@user_1171569875

Does NOT fit Dewalt track.

The designer has replied

@user_3560681765

is this a newer version of the track?

@user_1171569875

No, orginal version. The Dewalt track is different than the Festool, it is symmetric, with the channel in the center. I printed this to check and can confirn it does not fit the Dewalt style track.

@DownloadABear

Every track saw review I read and watched mentioned the DeWalt track is different from the Festool/Makita profile.

@CH46

Does the angle fit the current Bosch FSN rails

The designer has replied

Show original

@user_4062775276

I Just printed this and it doesn't fit the bosch fsn rails.

@user_3560681765

is the fsn a newer version? i tested it with one version a friend had and it worked

@Atterek

Replying to @user_3560681765 :

I can confirm it doesn't fit new FSN track, or I don't know how to mount it on there 🤔

@rhh5690

does this fit DeWalt or not. I am confused

The designer has replied

@user_3560681765

not in its current form i am told

@rhh5690

Replying to @user_3560681765 :

I Will wait printing then 🤓

@user_3560681765

Replying to @rhh5690 :

if you have the spacing measurements for the dewalt i can make it, atm i am a little busy to go track down a track for it to model off of

@jaeseopark

Hey thanks for sharing, are there any pictures of the piece in use?

The designer has replied

@user_3560681765

yeah, im away from my computer right now but when im back i can upload those

@packetspyke

Replying to @user_3560681765 :

i'll just sit with the others while we wait

@user_3560681765

Replying to @packetspyke :

just updated

@user_1310626301

This is a useful model. It fits my Makita track, but is a bit loose. I'm not sure if I'll try to adjust the model, but it's not useful as a square with the current sloppy fit.

The designer has replied

@user_3560681765

please consult the new version that i just posted. it should fix the issue that you are having

@user_1310626301

Replying to @user_3560681765 :

I'll check it out. Thanks!

@user_3560681765

just updated

@3dPetter

I only find 1 version Looking for the Dewalt version Thanks

Show original

@8t87jgn49n

Print Profile

0.2mm layer, 3 walls, 15% infill

ill-fitting

Show original

@user_3560681765

just updated

@djroanmd

Can EASEMAN tracks be used

The designer has replied

Show original

@user_3560681765

I haven't tested it with those

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.