hard to put together till you figure out the trick. put the head in first, then the lower center section with only the two front legs, if you hold the shell upside down you can insert one pair of legs at a time, then slide it down to secure them.
do that with all then drip some glue down there and push the half moon piece in place. followed by the tail.
printed in Kingroon PLA SILK Red/copper

LiterallyMiatas

0.16mm layer, 2 walls, 15% infill

can you tell me the length of the lobster when assembled please 

Maiye

the body is 5-6 inches with claws and antenna out to 8 inches 

Danke für die gute und hilfreiche Beschreibung!

Thank you for the good and helpful description

Look no further, this is "the" lobster model benchmark! when you take the time and care to clean up any rough edges and do the pins carefully (I use my Leatherman to push them in a few mm at the time and put just a spot of crazy glue on the ends of any that were loose so they wouldn't slide out). Also just a dab of glue inside on the main body sections to hold it all together. Great model! I might try scaling this one up

user_2213118899

skaliert auf 200%, schönes Ergebnis 👍🏻

profi-777

K.H.

L'unica difficoltà è nello spingere i fili dentro i buchi per il resto risultato bellissimo 

The only difficulty is pushing the wires into the holes otherwise the result is beautiful

Misaxorr

user_3653619031

UT.LAB

Heilandzack

putting it together is a little tricky but the holes are for filament sticks, I used a soldering iron to melt the ends round, you can see it because I used black. worked nicely but there was some holes I drilled out just to make it assemble easier.

user_883637185

Went together well, very nicely designed.

loganb

火宅

cover

微信图片_20240424184959_3f93d973-d337-4303-ad1c-c49f8af6ea58.jpg

微信图片_20240424185004_c4f6320c-c951-473a-bea5-bddce107e785.jpg

微信图片_20240424185010_191d30c6-f8f0-4352-9888-9335f5822b34.jpg

plate_1.png

neexus

tempImage8BA7R7.jpg

plate_2.png

plate_3.png

PXL_20260427_105739946.jpg

When printing Plate 2 (the plate for the legs) from the default profile, Bambu handy placed one of the rods (used as pins for pinning the parts together) outside of the print plate, and plated the other directly across the legs ruining the print.&nbsp;This profile prints both rods diagonally in between the legs so that you can print from Bambu Handy on your A1 Mini.&nbsp;Everything else left the same.

A1 Mini Optimized - 0.16mm layer, 2 walls, 15% infill

https://www.threeing.cn/model/detail/16h6s209833d658pi0

对原版进行了改进：1.把大钳子放大为150%，使之看上去更加霸气；2.加入了两根圆柱作为轴，原版是采用耗材丝做轴的，不能进行缩放打印，经过改进后可随意缩放打印；3.增加了必要的支撑，使打印成功变得更加轻松。Improvements have been made to the original:1. Enlarge the large pliers to 150% to make it look more domineering;2. Two cylinders are added as bolts, the original version is made of filament wire, which can not be scaled and printed, and can be scaled and printed at will after improvement;3. Added the necessary support to make it easier to print successfully.

Improvements have been made to the original:1. Enlarged the large claws to 150%, making them appear more domineering;2. Added two cylinders as axles, the original version used filament wire as axles, which could not be scaled and printed, and after improvement, it can be scaled and printed at will;3. Added necessary supports to make printing successful easier.

Print Profile(2)

Description

Comment & Rating (73)

This remix is based on

License

Related Models

Lobster