Logic connect 4 - Free 3D Print Model

Search models, users, collections, and posts

3Dprint-K81

Toys & Games>Board Games

IP Report

GIF

Print Profile(4)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

4.5 h

3 plates

4.0(39)

0.2mm layer, 2 walls, 15% infill

Designer

2.3 h

1 plate

3.8(4)

No Logo, One Plate, Easy Supports, Better Quality

4.9 h

1 plate

4.7(11)

full balls without logo

6.7 h

3 plates

Open in Bambu Studio

Boost

413

965

126

682

397

Released

Description

Try to get four marbles of your colour in a horizontal, vertical or diagonal row on the shifting game board.

But watch out! To finish your turn, you must press the central button, which will make all marbles shift one position on game board.

Stay focused as all marbles change position on every turn!

Moreover, you can also disrupt your opponent's strategy by moving one of their marbles on your turn.

Insert a spring (you can take it from a normal writing pen, see photo) or if you want you can buy one on Amazon (LINK):

QUARKZMAN Compressione Molla, 5pz 304 Acciaio Inossidabile, 6mm OD, 0.6mm Filo Dimensione, 15mm Libero Lunghezza, Argento Tono : Amazon.it: Commercio, Industria e Scienza

Have fun and good luck!!!

Enjoy print and I look forward to your rating and feedback…thanks!

Comment & Rating (126)

@ME3DPrint

Thank You. Connect 4 is a classic. Took me about 20 mins to clean up that white part! :-| My fingers are probably a bit big when pressing the button :)

The designer has replied

@3DprintK81

if you have problems pressing the central button you could also do it on the sides with two hands. I added a profile for the main table with supports that are easier to remove and modified the existing one (with normal supports). If you feel like it, you can rate my project with stars... I thank you if you can ❤️

@NiceMemeMaster

I did the special version and do I have to remove these supports to? I mean are these supports?

@user_2131453775

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

The supports for the top part were incredibly difficult to remove, even with pliers. The mechanism to move the pieces each turn is pretty finicky; not all pieces move reliably, and since the knob at the center is so low (I guess I understand the reasoning, though) my finger can interfere with the movement of the pieces in the center square. It is, however, a clever design and I like the concept.

The profile uploader has replied

@3DprintK81

thx❤️

@lirian.aitlhadj

Print Profile

0.2mm layer, 2 walls, 15% infill

I'm a bit disgusted, it takes at least 30 minutes of calibration for this. Either give correct states, but I'm adding a star for the friendliness of the person who created it

(Edited)

The profile uploader has replied

Show original

@3DprintK81

I'm sorry but it's very strange try to calibrate your printer

Show original

@lirian.aitlhadj

Replying to @3DprintK81 :

ok thank you I'll see

Show original

@toppsikrett

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

Very nice thank you

The profile uploader has replied

@3DprintK81

THX ❤️❤️

@Ulrich_Driessen

I had problems with the spring then created my own spring solution with hot glue (Picture)

The designer has replied

Show original

@3DprintK81

thx❤️

@user_1637665090

Hello, Could you please explain how to play this game? I have printed it, but I didn’t understand how to use it or play it.

The designer has replied

@3DprintK81

it is played by two players. you place one ball at a time on a square you want and at each turn press the table (so the spheres move). The winner is the one who after pressing completes 4 balls in a row (horizontal, vertical, or diagonal)

Show original

@benpark20

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

super fun and challenging to play

(Edited)

The profile uploader has replied

@3DprintK81

thx👍🏻

@SmonstrStudio

Print Profile

0.2mm layer, 2 walls, 15% infill

nice game! sometimes the balls don't roll over properly. so you have to be attentive 🤖

The profile uploader has replied

@3DprintK81

thx ❤️

@KaffineAddict

Print Profile

0.2mm layer, 2 walls, 15% infill

This came out really good. Simple print. Fun to play

The profile uploader has replied

@3DprintK81

wonderful...you chose some nice colors, great choice 👍🏻

@user_2458429393

Print Profile

0.2mm layer, 2 walls, 15% infill

The profile uploader has replied

@3DprintK81

thx❤️

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.