Search models, users, collections, and posts

Micro SD Card Holder

bgill
Tools>Organizers
IP Report

Print Profile(4)

All
P1P
P1S
X1
X1 Carbon
X1E
A1
A1 mini
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L
0.2mm layer, 2 walls, 100% infill
0.2mm layer, 2 walls, 100% infill
Designer
40 min
1 plate
4.4(127)
0.15mm layer, 2 walls, 20% infill, no stringing on lid
0.15mm layer, 2 walls, 20% infill, no stringing on lid
52 min
1 plate
4.9(31)
0.24mm layer, 2 walls, 20% infill
0.24mm layer, 2 walls, 20% infill
40 min
1 plate
4.3(44)
Lid with threads that work
Lid with threads that work
22 min
1 plate
4.8(5)
Open in Bambu Studio
Boost
355
988
254
67
2.8 k
2.1 k
Released 

Description

Ever forgot your Micro SD cards at home or in the other bag - or even worst - lost it because they are so small?

The Micro SD Card Holder allows you to protect and carry your cards always with you. The cylindric container (3,8 cm in diameter) can get unscrewed and holds up to 12 Micro SD Cards in the bottom shell. The cards are held by springs, so they do not fall out, even if you turn the bottom part upside down. At the same time the springs only cause gentle pressure - enough to hold the card, but not damage it.



sd card holder
sdcard
micro sd card
microsdcardholder

Comment & Rating (254)

(0/1000)
@PrintTech101
Print Profile
0.2mm layer, 2 walls, 100% infill
Nice model but threads did not work
The profile uploader has replied
3
Reply
@Shyjang1
My A1 print came out just like yours, standard speed print
Show original
0
Reply
@bgill
You need to print with slower speed. With the older Bambulab Firmware this problem did not occur, but with the later ones it does.
0
Reply
@KellyDesigns3D
Print Profile
0.2mm layer, 2 walls, 100% infill
Had issues with the threads on the lid but otherwise it was great
The profile uploader has replied
1
Reply
@bgill
You need to print the lid with a lower speed
0
Reply
@MoarPrints
Replying to @bgill :
I had the same problem with the lid. Kind of expected your .3mf to already have slower speed on the lid if it needed it.
0
Reply
@MFKDGAF
Replying to @MoarPrints :
Same. Lid did not print as expected and was stringy. If the lid needs to be printed at a slower speed, the .3mf file should have had that cnfigured.
0
Reply
@user_1022642586
Print Profile
0.24mm layer, 2 walls, 20% infill
didn't go that well for the lid, but otherwise good idea
2
Reply
@wukis
Yes, same problem.
(Edited)
1
Reply
@user_1098466061
The print profile is no longer public
super handy
2
Reply
@user_1076902293
Print Profile
0.2mm layer, 2 walls, 100% infill
Perfect just what I needed.
0
Reply
@NicoX3d
Print Profile
0.15mm layer, 2 walls, 20% infill, no stringing on lid
great tolerance, nice project
Show original
0
Reply
@user_3670996646
Print Profile
0.15mm layer, 2 walls, 20% infill, no stringing on lid
fantastic print
0
Reply
@user_355596581
Print Profile
0.2mm layer, 2 walls, 100% infill
everything was perfect except for the threads in the cap
0
Reply
@user_1422720257
Print Profile
0.15mm layer, 2 walls, 20% infill, no stringing on lid
Nice design. No stringing problem
0
Reply
@walker_prints
Boosted
Print Profile
Lid with threads that work
Much better
0
Reply

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivatives

Related Models

Jeep Kit Card
Jeep Kit Card
agepbiz
71 k
22 k
Cascade card wallet V2
Cascade card wallet V2
Hugo
53.5 k
13.9 k
T-Rex Skeleton Kit Card
T-Rex Skeleton Kit Card
Fletch
42.3 k
15.2 k
SD Card Case - SD & Micro SD
SD Card Case - SD & Micro SD
Maxx Design
1.5 k
534