J2$hortt

pic4.jpg

cover

20260517_091646.jpg

20260517_091653.jpg

20260517_091659.jpg

20260517_091713.jpg

cults pic 1.jpg

pic5.jpg

pic3.jpg

pic2.jpg

pic1.jpg

plate_1.png

6d5c380db8c8ba88.jpg

<p>For this specific Canon eyecup model, the goal with <strong>Arachne</strong> is:</p><ul><li>preserve tiny rail geometry,</li><li>avoid over-thickened edges,</li><li>maintain accurate slide fit,</li><li>and maximize wall continuity on the thin curved sections.</li></ul><p>Bambu Studio’s default Arachne settings are decent, but for <i>small precision mechanical parts</i> like this, you can tune them noticeably better.</p><p>Here’s the setup I’d recommend.</p><h2>Optimal Arachne Settings</h2><h2>For Small Precision Parts</h2><h3>(Canon Eyecup / Clips / Rails / Small Snap Fits)</h3><h2>Recommended Settings</h2><figure class="table"><table><thead><tr><th>Setting</th><th>Recommended Value</th></tr></thead><tbody><tr><td>Wall Generator</td><td>Arachne</td></tr><tr><td>Min Feature Size</td><td>15–25%</td></tr><tr><td>Min Wall Width</td><td>60%</td></tr><tr><td>Wall Transition Length</td><td>50%</td></tr><tr><td>Wall Transition Filter Margin</td><td>25%</td></tr><tr><td>Detect Thin Walls</td><td>ENABLED</td></tr><tr><td>Precise Wall</td><td>ENABLED</td></tr><tr><td>Only One Wall on Top Surfaces</td><td>DISABLED</td></tr></tbody></table></figure><h2>What These Actually Do</h2><h2>1. Min Feature Size</h2><h2>Recommended:</h2><ul><li><strong>15–25%</strong></li></ul><h3>Why</h3><p>This tells Arachne:</p><blockquote><p>“Preserve tiny geometry instead of deleting it.”</p></blockquote><p>Critical for:</p><ul><li>eyecup rails,</li><li>tiny retention lips,</li><li>curved edges.</li></ul><h3>My Preferred Value</h3><ul><li><strong>20%</strong></li></ul><p>Good balance between:</p><ul><li>preserving details,</li><li>avoiding weird extrusion artifacts.</li></ul><h2>2. Min Wall Width</h2><h2>Recommended:</h2><ul><li><strong>60%</strong></li></ul><p>For a 0.4 nozzle:</p><p>0.24 mm effective minimum
</p><h3>Why</h3><p>Allows Arachne to:</p><ul><li>create narrower adaptive walls,</li><li>preserve thin sections,</li><li>avoid overbuilding the rails.</li></ul><h3>Avoid:</h3><ul><li>80–100%</li></ul><p>That makes small parts bulky and dimensionally inaccurate.</p><h2>3. Wall Transition Length</h2><h2>Recommended:</h2><ul><li><strong>50%</strong></li></ul><h3>Why</h3><p>Controls how gradually wall widths change.</p><p>For precision parts:</p><ul><li>smoother transitions,</li><li>better dimensional consistency,</li><li>fewer pressure spikes.</li></ul><h3>If Too Low</h3><p>You get:</p><ul><li>abrupt extrusion width changes,</li><li>blobs,</li><li>uneven rail surfaces.</li></ul><h2>4. Wall Transition Filter Margin</h2><h2>Recommended:</h2><ul><li><strong>25%</strong></li></ul><h3>Why</h3><p>Helps smooth tiny adaptive-width fluctuations.</p><p>For small rails:</p><ul><li>improves consistency,</li><li>reduces jittery wall paths.</li></ul><h2>5. Detect Thin Walls</h2><h2>ENABLE THIS</h2><p>Critical.</p><p>Without it:</p><ul><li>tiny rail geometry may partially disappear,</li><li>or print inconsistently.</li></ul><h2>6. Precise Wall</h2><h2>ENABLE THIS</h2><p>(if available in your Bambu Studio version)</p><p>This helps:</p><ul><li>dimensional accuracy,</li><li>wall placement,</li><li>rail fitment tolerances.</li></ul><p>Very useful for:</p><ul><li>slide-fit parts,</li><li>clips,</li><li>camera accessories.</li></ul><h2>7. Only One Wall on Top Surfaces</h2><h2>DISABLE THIS</h2><p>You want:</p><ul><li>full wall reinforcement,</li><li>especially around the curved upper lip.</li></ul><h2>Additional Settings That Pair VERY Well With Arachne</h2><h2>Outer Wall Line Width</h2><h2>Recommended:</h2><ul><li>0.42 mm</li></ul><h2>Inner Wall Line Width</h2><h2>Recommended:</h2><ul><li>0.45 mm</li></ul><h2>Top Surface Line Width</h2><h2>Recommended:</h2><ul><li>0.40 mm</li></ul><h2>Small Perimeter Speed</h2><h2>Recommended:</h2><ul><li>15–20 mm/s</li></ul><p>This matters enormously with Arachne.</p><h2>Flow Ratio</h2><h2>Calibrate Carefully</h2><p>Arachne exposes overextrusion problems much more visibly.</p><p>For PETG:</p><ul><li>slightly UNDER-extruded is often better for fitment.</li></ul><h2>Best Combo for This Exact Part</h2><h2>Material</h2><p>PETG</p><h2>Nozzle</h2><p>0.4 mm</p><h2>Layer Height</h2><p>0.12 mm</p><h2>Walls</h2><p>4</p><h2>Arachne Settings</h2><ul><li>Min Feature Size:<ul><li>20%</li></ul></li><li>Min Wall Width:<ul><li>60%</li></ul></li><li>Transition Length:<ul><li>50%</li></ul></li><li>Filter Margin:<ul><li>25%</li></ul></li></ul><h2>Detect Thin Walls</h2><p>ON</p><h2>Precise Wall</h2><p>ON</p><h2>Elephant Foot Compensation</h2><p>0.18 mm</p><h2>XY Compensation</h2><p>-0.04 mm</p><h2>One Important Warning</h2><p>Arachne can sometimes make:</p><ul><li>snap-fit tabs,</li><li>slide rails,</li><li>and press-fit parts</li></ul><p>VERY slightly oversized.</p><p>So after your first print:</p><ul><li>test fit FIRST,</li><li>then tune:<ul><li>XY compensation,</li><li>or horizontal expansion.</li></ul></li></ul><p>Usually:</p><p>-0.02 to -0.06 mm
</p><p>fixes it.</p><h2>If You Want the BEST Possible Surface Quality</h2><p>Enable:</p><h2>“Slow printing down for better layer cooling”</h2><p>AND</p><p>Print:</p><ul><li>2 eyecups simultaneously.</li></ul><p>That gives tiny layers enough cooling time and noticeably improves:</p><ul><li>corners,</li><li>rail sharpness,</li><li>surface consistency.</li></ul>

0.12mm layer, 3 walls, 100% infill

<p>Replacement Canon EF Eyecup (Canon P/N 8171A001) for select Canon EOS DSLR and film cameras. Attaches to the camera viewfinder to provide cushioning, improve comfort, and help block stray light while shooting. Original model created by 3DPrintingOne and published on Cults3D on Nov 13, 2017 (Design #16766). Original description: “Replacement Canon Eyecup (Black) look for the small green arrow to understand which part it is.”</p><boostme><boosttitle>Boost Me</boosttitle><boostcontent>Boost this model to raise awareness of its original Authors work!</boostcontent></boostme>

Canon EF Eyecup | Canon P/N#: 8171A001

ASIA

Print Profile(1)

Description

Documentation (1)

Comment & Rating (0)

License

Related Models