Linksys Velop MX4000 Series Wall Mount - Free 3D Print Model

Search models, users, collections, and posts

Printsmiths

Tools>Gadgets

IP Report

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 6 walls, 25% infill

5.5 h

2 plates

5.0(1)

Open in Bambu Studio

Boost

114

Released

Description

An easy print, this wall mount perfectly and securely mates with your Linksys Velop MX4000 series routers. The model shown was printed in Polymaker PolyTerra PLA in Army Green on Prusa Minis. Print the Case, the Mount, and two Keys. Assembly was done with a gel super glue. Cutouts in the Case provide adequate workable space for a screwdriver or driver to wall-mount.

Comment & Rating (19)

@jarppinen

Print Profile

0.2mm layer, 6 walls, 25% infill

Looks good, prints great. Have to do three more.

@user_3209548236

worked like a champ. gonna see if I can build in a cable wrap

@user_340284699

Boosted

Absolutely fantastic piece I cannot concur with the negative reviews Some images from previous reviewers show poorly printed parts with insufficient bed adhesion The two parts fit together perfectly printed on a Bambu X1C A small tip Arrange the two parts additionally vertically merged as a single file The support structure on the inside is not visible and thus you even have one component Keep up the great work Double boost is out

(Edited)

Show original

@dampney

The print profile is no longer public

Similar to the comments below, the base mount isn’t flat so there is an awkward support layer. the base didnt print flat and warped at a corner. It’s a nice design that needs work but the biggest issue I have is the lack of open slots for the Routers bottom vents. The Linksys router uses the bottom vents to pull air through the tower and shoots the hot air out the top.

@wissenspirat

The print profile is no longer public

Other Issues:The bottom part doesn't print cleanly, the base and perimeter are prone to breaking away like supports, leaving holes I've printed it twice now, with other projects in between, but this one hasn't printed cleanly for me yet

Show original

@Spikedbyike1

The print profile is no longer public

The profile uploader has replied

@tandtdesignsms

Why only 4 stars?

@Spikedbyike1

Replying to @tandtdesignsms :

so the top piece printed perfect when I tried with petg and pla. (2 different attempts). mount (bottom) messed up on both. like the previous picture someone had. it wants to do a Wavy edge and the guide triangles don't even both remove from the bottom piece. i also broke it down and did it over each individual piece for printing to make sure that wasn't the problem. this print caused the 1st 1st layer error I have gotten on this x1c gave it a 4 for effort and that half of it was perfect. minus 1 for the problem with bottom piece

(Edited)

@tandtdesignsms

Replying to @Spikedbyike1 :

Thank you for the response! I’ll look into it and fix it tonight!

@DatumCAD

For some reason the internal dims of your 'case' model part (where the router base sits) measures approx. 114mm x 114mm when the router base is a fair bit smaller..... around 86mm x 86mm. Is the scaling off in your uploaded print file perhaps? Love the design....just trying to figure out why its so much larger than measured before I print one for my routers. Cheers Matt

(Edited)

The designer has replied

@Printsmiths

There is no scaling. The measurements are correct. What is likely the case is that you are using a different router; Linksys makes numerous of various widths and sizes. I made stands for only two of them.

@DatumCAD

Replying to @Printsmiths :

You’re quite right as mine is a MX2000 which online measurements are given as 3.4inches (86mm) and match that I have measured too. But the dims for the MX4000 are actually given as smaller still…..at 3.1inches (79mm) which is why I thought I would check the scaling with you…. 114mm seemed larger than any of the online information.

(Edited)

@user_920613951

Boosted

Thank you so much for making this. I just printed this for my mx4300 and it fit perfectly. The only issue I had was the bottom portion seems to not be flat in the design uploaded so it creates supports underneath what should be a flat object and makes the print take much longer. The top printed perfectly.

@jarppinen

Works great. Printed with Bambu H2S and quality is great.

@mikekep

Boosted

Thank you 👍 perfect fit Exactly what I was looking for

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Wall Hook with one Mount

PrintManufaktur

22.4 k

8.3 k

IKEA Skadis Wall Mount

AU3D

31.9 k

9.9 k

Guitar Wall Mount

VICLER

22.4 k

5.9 k

Headphone Hanger Wall Mount

Westbound

26 k

5.4 k