LayerForge

cover

IMG_20260508_171802.jpg

IMG_20260508_171807.jpg

IMG_20260508_171815.jpg

plate_1.png

62e425fb55a78c1a.png

<p><strong>PLA 0.2mm – Standard – P2S</strong></p><p>&nbsp;</p><p>Profilo derivato dal preset <strong>0.20mm Standard @BBL P2S</strong> di Bambu Studio, calibrato per figurine organiche con geometria complessa. Le impostazioni di infill al 10% sono intenzionalmente contenute. Trattandosi di un modello solido non strutturale, l&#39;obiettivo è ridurre il peso e il consumo di filamento senza compromettere la rigidità superficiale, garantita da 5 layer superiori e 3 inferiori. Il supporto tree organic con stile &#34;organic&#34; e distanza Z di 0.21 mm favorisce un distacco pulito sulle zone di mantello e corona, particolarmente critiche. La velocità della parete esterna è ridotta rispetto al default (100 mm/s) per preservare la resa dei dettagli fini.</p><figure class="table"><table><thead><tr><th>Parametro</th><th>Valore</th></tr></thead><tbody><tr><td>Layer height</td><td>0.2 mm</td></tr><tr><td>Perimetri</td><td>2</td></tr><tr><td>Infill</td><td>10% – Grid</td></tr><tr><td>Top / Bottom layers</td><td>5 / 3</td></tr><tr><td>Velocità parete esterna</td><td>100 mm/s</td></tr><tr><td>Velocità parete interna</td><td>250 mm/s</td></tr><tr><td>Supporti</td><td>Tree Organic – solo dal piano</td></tr><tr><td>Distanza Z supporto</td><td>0.21 mm</td></tr><tr><td>Temperatura ugello</td><td>220 °C</td></tr><tr><td>Temperatura piano</td><td>40 °C (Supertack)</td></tr><tr><td>Materiale testato</td><td>Bambu PLA Basic</td></tr></tbody></table></figure>

<p><strong>PLA 0.2mm – Standard – P2S</strong></p><p>&nbsp;</p><p>Profile derived from the <strong>0.20mm Standard @BBL P2S</strong> preset of Bambu Studio, calibrated for organic figurines with complex geometry. The 10% infill settings are intentionally kept low. As this is a non-structural solid model, the goal is to reduce weight and filament consumption without compromising surface rigidity, which is ensured by 5 top and 3 bottom layers. The tree organic support with 'organic' style and a Z distance of 0.21 mm promotes clean detachment in the critical cloak and crown areas. The outer wall speed is reduced compared to the default (100 mm/s) to preserve fine detail rendering.</p><figure class="table"><table><thead><tr><th>Parameter</th><th>Value</th></tr></thead><tbody><tr><td>Layer height</td><td>0.2 mm</td></tr><tr><td>Perimeters</td><td>2</td></tr><tr><td>Infill</td><td>10% – Grid</td></tr><tr><td>Top / Bottom layers</td><td>5 / 3</td></tr><tr><td>Outer wall speed</td><td>100 mm/s</td></tr><tr><td>Inner wall speed</td><td>250 mm/s</td></tr><tr><td>Supports</td><td>Tree Organic – from build plate only</td></tr><tr><td>Support Z distance</td><td>0.21 mm</td></tr><tr><td>Nozzle temperature</td><td>220 °C</td></tr><tr><td>Bed temperature</td><td>40 °C (Supertack)</td></tr><tr><td>Tested material</td><td>Bambu PLA Basic</td></tr></tbody></table></figure>

0.2mm layer, 2 walls, 10% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

<p>Il sovrano più maestoso della Terra di Mezzo prende forma in ogni dettaglio, lembi del mantello regale che sfiorano il suolo. <br><br>Questa figurine di <strong>Thranduil, il Re degli Elfi</strong>, cattura tutta l&#39;alterigia e la grazia del personaggio iconico de <i>Lo Hobbit</i> e <i>Il Signore degli Anelli</i>.</p><p>&nbsp;</p><h4>🖨️ Compatibilità</h4><ul><li><strong>Stampante testata:</strong> Bambu Lab P2S</li><li><strong>Stampanti compatibili:</strong> Bambu Lab A1, H2S, H2D, H2D Pro, H2C, X2D (ugello 0.4mm)</li><li><strong>Ugello:</strong> 0.4 mm</li><li><strong>Piano di stampa: </strong>BiQu CryoGrip</li><li><strong>Pezzo unico:</strong> nessun assemblaggio richiesto</li></ul><h4>📐 Specifiche Tecniche</h4><figure class="table"><table><thead><tr><th>Parametro</th><th>Valore</th></tr></thead><tbody><tr><td>Altezza di stampa</td><td>~135 mm</td></tr><tr><td>Impronta sul piano</td><td>~100 × 86 mm</td></tr><tr><td>Materiale testato</td><td>Bambu PLA Basic</td></tr><tr><td>Layer height</td><td>0.2 mm</td></tr><tr><td>Infill</td><td>10% (griglia)</td></tr><tr><td>Perimetri</td><td>2</td></tr><tr><td>Layer superiori / inferiori</td><td>5 / 3</td></tr><tr><td>Supporti</td><td>✅ Sì — Tree Organic, solo dal piano</td></tr><tr><td>Orientamento</td><td>Ottimizzato dallo slicer (inclinato per ridurre supporti su zone critiche)</td></tr><tr><td>Temperatura ugello</td><td>220 °C</td></tr><tr><td>Piano di stampa</td><td>40 °C (Supertack)</td></tr></tbody></table></figure><h4>💡 Consigli di Stampa</h4><ul><li>🌲 Il <strong>supporto tree organic</strong> gestisce bene i sottosquadra tipici di mantello e corona — non rimuovere i preset del profilo.</li><li>🧹 Al termine della stampa, rimuovi i supporti con cura usa pinzette a punta fine per non danneggiare le parti sottili.</li></ul><boostme><boosttitle>Boost Me</boosttitle><boostcontent>Se Thranduil ha trovato posto sulla tua scrivania, lascia un like ❤️ o un boost 🚀, mi aiuta tantissimo a continuare la serie della Terra di Mezzo. </boostcontent></boostme>

<p>The most majestic sovereign of Middle-earth takes shape in every detail, with the edges of his regal cloak sweeping the ground. <br><br>This figurine of <strong>Thranduil, the Elven King</strong>, captures all the haughtiness and grace of the iconic character from <i>The Hobbit</i> and <i>The Lord of the Rings</i>.</p><p>&nbsp;</p><h4>🖨️ Compatibility</h4><ul><li><strong>Tested printer:</strong> Bambu Lab P2S</li><li><strong>Compatible printers:</strong> Bambu Lab A1, H2S, H2D, H2D Pro, H2C, X2D (0.4mm nozzle)</li><li><strong>Nozzle:</strong> 0.4 mm</li><li><strong>Print bed: </strong>BiQu CryoGrip</li><li><strong>Single piece:</strong> no assembly required</li></ul><h4>📐 Technical Specifications</h4><figure class="table"><table><thead><tr><th>Parameter</th><th>Value</th></tr></thead><tbody><tr><td>Print height</td><td>~135 mm</td></tr><tr><td>Footprint on bed</td><td>~100 × 86 mm</td></tr><tr><td>Tested material</td><td>Bambu PLA Basic</td></tr><tr><td>Layer height</td><td>0.2 mm</td></tr><tr><td>Infill</td><td>10% (grid)</td></tr><tr><td>Perimeters</td><td>2</td></tr><tr><td>Top / Bottom layers</td><td>5 / 3</td></tr><tr><td>Supports</td><td>✅ Yes — Tree Organic, from build plate only</td></tr><tr><td>Orientation</td><td>Optimized by slicer (tilted to reduce supports on critical areas)</td></tr><tr><td>Nozzle temperature</td><td>220 °C</td></tr><tr><td>Print bed</td><td>40 °C (Supertack)</td></tr></tbody></table></figure><h4>💡 Printing Tips</h4><ul><li>🌲 <strong>Tree organic support</strong> handles typical undercuts of cloak and crown well — do not remove profile presets.</li><li>🧹 After printing, carefully remove supports using fine-tipped tweezers to avoid damaging delicate parts.</li></ul><boostme><boosttitle>Boost Me</boosttitle><boostcontent>If Thranduil has found a place on your desk, leave a like ❤️ or a boost 🚀, it helps me a lot to continue the Middle-earth series. </boostcontent></boostme>

Print Profile(1)

Description

🖨️ Compatibility

📐 Technical Specifications

💡 Printing Tips

Comment & Rating (2)

License

Related Models

Parameter	Value
Print height	~135 mm
Footprint on bed	~100 × 86 mm
Tested material	Bambu PLA Basic
Layer height	0.2 mm
Infill	10% (grid)
Perimeters	2
Top / Bottom layers	5 / 3
Supports	✅ Yes — Tree Organic, from build plate only
Orientation	Optimized by slicer (tilted to reduce supports on critical areas)
Nozzle temperature	220 °C
Print bed	40 °C (Supertack)

Thranduil - The Hobbit