WRITE - Reusable Notebook - Free 3D Print Model

Search models, users, collections, and posts

Tennow Corp.

Household>Office

IP Report

GIF

Print Profile(1)

All

P2S

P1P

H2D

H2S

H2C

X1 Carbon

X2D

P1S

H2D Pro

X1E

A2L

0.2mm layer, 2 walls, 15% infill

Designer

1.8 h

2 plates

4.5(11)

Open in Bambu Studio

Boost

786

2774

617

334

Released

Description

This reusable notebook was designed to combine simplicity, modularity, and durability.

⚙️ How it works:
Cut an A4 sheet in half, fold it, and insert it into the module to refill the notebook.

🔹 Compact & portable design
🔹 Rigid surface for stable writing
🔹 Infinitely refillable system

Requirements

Two small pieces of wire are required for the hinge assembly.
An elastic band is required to hold the pages in place.

Comment & Rating (53)

@Sebb87

I like the idea, but I don't think it should be printed like this, should it

The designer has replied

Show original

@user_4276668149

have you modified the file to print? these two parts are normally glued, they form only one block

Show original

@Sebb87

Replying to @user_4276668149 :

I only selected the colors, nothing else. I did it from my phone, I will try again from the PC

Show original

@user_4276668149

Replying to @Sebb87 :

normally if you don't modify my file everything should print correctly

Show original

@leontinker

Print Profile

0.2mm layer, 2 walls, 15% infill

I think I need to print it slightly bigger... The filament didn't run through the unions.. Edit: I didnt read the "!Two small pieces of wire are required for the hinge assembly." part... my mistake

(Edited)

The profile uploader has replied

@user_4276668149

the filament does not pass through it needs to be done using wire as specified in the description and on the gif

(Edited)

Show original

@leontinker

Replying to @user_4276668149 :

And thats why I need to read completely before posting... thank you

(Edited)

@user_4276668149

Replying to @leontinker :

no problem, I hope you have a bit of wire :)

(Edited)

Show original

@Wilson551

front cover split as soon as it came off the plate. It does not stay together. Will have to print another back piece to use this… Did not change any settings, just printed as it was.

The designer has replied

@chadisfred

Had the same issue taking it off the cool plate.

@user_4276668149

honestly I don't know why it works for some people and not others I'm new to printing and 3D creation my model prints well every time and I've had a lot of 5-star ratings so I think printing works for most people I don't understand why it's different for some what printer do you have and what material did you print with do you have the AMS

Show original

@Wilson551

Replying to @user_4276668149 :

I have the A1 with the AMS lite. it looked like it was going to print fine, then when I picked it up I noticed that ot was not fully attached and came right apart. it is a great design, but I think the separation line is too deep. I’m not sure.

@Checco0505

Print Profile

0.2mm layer, 2 walls, 15% infill

honestly, this is a great model. printed this to have an universal notebook for school and it turned out great.

The profile uploader has replied

@user_4276668149

thank you for your comment :) this is really great in blue !

(Edited)

@user_4079843660

you should build a stencil to lay over the pages and we can draw lines nice and easy and turn it into a journal

The designer has replied

@user_4276668149

that's a good idea, I will do it :) thank you for your feedback !

@physengrad

Can the regular filament be used for the wire in here? I've seen other notebook models using the filament as wire, and I think that is clever way to do it. The design looks cool, and I'd like to print it, but I would very much appreciate confirmation regarding the wire thing.

The designer has replied

@user_4276668149

the filament doesn't fit in here, in order to have a stronger and smaller mecanism, allowing you to have more flat surface to write

@brids81

Replying to @user_4276668149 :

which diameter wire is needed to fit in?

@user_4276668149

the hole is 1.8 mm i have 3 different wire cables and all fit in :)

Show original

@FilipaGM

I've printed one for my daughter, turned out great! I used purge lines instead of wire because it was what I had in hand and it seems to work suprisingly well 😂 About the issue of separating parts, you could try to play around with the beam interlocking properties

@jneuhaus1987

Love it. I really want to brainstorm a latch or something that locks into place to replace the rubber band. 🤔

The designer has replied

@user_4276668149

yes that's a good idea, I'll think about it :) thank you for your comment

Show original

@Little_Grub

Love the design, any chance you can make it expandable? It would be great if there were extra hinge pieces that could be added as you need. This could then expand to hold more pages. would be brilliant as an A5 expandable binder...

The designer has replied

@user_4276668149

yes that would be a great idea thank you

Show original

@user_1822892566

Print Profile

0.2mm layer, 2 walls, 15% infill

cute notebook!

The profile uploader has replied

@user_4276668149

thank you 😊

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.