EXCLUSIV3D

Cinta adhesiva de silicona de doble cara reutilizable con anche de 3cm

cover

Soporte 05.png

Soporte 04.png

Soporte GIF.gif

Soporte 01.png

Soporte 02.png

Soporte 03.png

plate_1.png

Impresión resultado.jpg

-Altura de capa 0.20mm-Impresión sin soportes-4 paredes-15% relleno&nbsp;Con esta configuración, me aseguré que el punto más crítico, estuviera reforzado (Aunque no va a ser sometido ni a soportar esfuerzos intensos, a menos que lo hagamos nosotros mal).&nbsp;La base con este relleno, es mas que suficiente.&nbsp;Se puede imprimir sin soportes perfectamente.&nbsp;Podría imprimirse en vertical para mayor resistencia en la unión entre base y el soporte de pared, pero insisto, si no lo sometemos a esfuerzo innecesarios, aguanta perfectamente.&nbsp;Imprimir en PETG para obtener los resultados previstos en las condiciones de uso estimadas.

-Layer height 0.20mm-Print without supports-4 walls-15% infill&nbsp;With this configuration, I ensured that the most critical point was reinforced (Although it will not be subjected to or withstand intense forces, unless we misuse it).&nbsp;The base with this infill is more than sufficient.&nbsp;It can be printed perfectly without supports.&nbsp;It could be printed vertically for greater strength at the joint between the base and the wall mount, but I insist, if we do not subject it to unnecessary stress, it holds up perfectly.&nbsp;Print in PETG to obtain the expected results under the estimated usage conditions.

0.2mm layer, 4 walls, 15% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including, but not limited to, publishing derivative works outside the Makerworld platform or hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money or collect fees.
Subject to the above restrictions, derivative works may be published only within the Makerworld platform, and all such derivative works must be licensed under the same SDFL‑C license, without modification or additional terms.
You may download the digital versions of this object, 3D print it, and display images, videos, or usage demonstrations of 3D printed versions of the object on personal social media platforms or Makerworld official channels, provided that no digital versions of the object are shared or distributed.

This work is licensed under a Standard Digital File License – Community Use (SDFL‑C).

Este diseño nació tras imprimir el maravilloso “Exprimidor de pasta de dientes con trinquete 7.0” de “Andrew3d”, y está adaptado exclusivamente a este modelo (Desconocemos la compatibilidad con otros diseños).&nbsp;Es un diseño sencillo que permite sostener el exprimidor sujeto a la pared,  manteniendo el lavabo despejado, y teniéndolo accesible siempre.Además, evita que se acumule agua bajo él, y permite tener una higiene óptima del entorno donde uno se asea.&nbsp;Está pensado para no taladrar el baño, y desgraciar tus azulejos. Se diseñó para colocar tras el soporte una tira de cinta de silicona de doble cara de 3cm de ancho. Se recomienda limpiar la superficie donde vaya a pegarse con alcohol de limpieza o similar para retirar suciedad que evite su correcta adhesión. Colocar con la superficie seca. Presionar durante unos 30 segundos, y dejar unas horas antes de colocar tu Toothpaste Squeezer 7.0.&nbsp;El diseño posee una ranura de desagüe para que no se estanque el agua bajo el exprimidor.&nbsp;La posición del exprimidor debe ser siempre con la zona del trinquete hacia la izquierda para mantener el diseño dentro del soporte.Para colocar el exprimidor, primero hay que introducir las patitas en los huecos destinados a ello mas cercanos a la pared, y tras esto, bajar las otras dos patas a las dos ubicaciones delanteras (Ver GIF para saber como).&nbsp;Imprimir en PETG para obtener resultados óptimos en las condiciones de uso previstas.

This design was created after printing the wonderful “Toothpaste Squeezer with Ratchet 7.0” by “Andrew3d”, and it is exclusively adapted to this model (We do not know its compatibility with other designs).&nbsp;It is a simple design that allows the squeezer to be held against the wall, keeping the sink clear and always accessible.In addition, it prevents water from accumulating underneath it, and allows for optimal hygiene in the environment where one washes.&nbsp;It is designed to avoid drilling into the bathroom and damaging your tiles. It was designed to place a 3cm wide strip of double-sided silicone tape behind the holder. It is recommended to clean the surface where it will be adhered with rubbing alcohol or similar to remove dirt that may prevent proper adhesion. Apply to a dry surface. Press for about 30 seconds, and leave for a few hours before placing your Toothpaste Squeezer 7.0.&nbsp;The design has a drainage slot to prevent water from stagnating under the squeezer.&nbsp;The position of the squeezer must always be with the ratchet area to the left to keep the design within the holder.To place the squeezer, first insert the small feet into the designated holes closest to the wall, and after this, lower the other two feet into the two front locations (See GIF to learn how).&nbsp;Print in PETG for optimal results under the intended use conditions.

Print Profile(1)

Bill of Materials

Description

Comment & Rating (1)

License