Rescue Box Nitrile Gloves - Free 3D Print Model

Search models, users, collections, and posts

Florian

Tools>Medical Tools

IP Report

GIF

Print Profile(2)

All

P1S

H2S

H2D Pro

P1P

H2C

X1 Carbon

X1E

P2S

H2D

X2D

A2L

Sliding lid with and without eyelet

Designer

1.4 h

1 plate

4.9(40)

Lid glued

Designer

1 h

1 plate

4.8(6)

Open in Bambu Studio

Boost

673

2449

1 k

689

Released

Bill of Materials

Bambu Filaments

Select all

PLA Basic

PLA Basic

PLA Basic

Description

Content has been automatically translated.

Show original

Membership

My Basic Commercial License on MakerWorld applies to this model. With an active subscription, printed copies may be sold. All details can be found in my profile.

Join

With the Rescue Box, you always have your nitrile gloves ready on your operational clothing and are perfectly equipped for your missions.

The box fits 4 nitrile gloves. The lid slides open, so the gloves can be refilled at any time.

The box has an eyelet on the top for a carabiner. This allows it to be attached anywhere on the operational clothing.

For everyone who simply wants to put it in a bag, there is a second print profile without an eyelet.

So you no longer have to carry your nitrile gloves individually in your pockets.

If you like the model, feel free to leave me a Boost and don't forget to rate and comment diligently.

UPDATE: Now new the V2 as a door wedge - Also check out the model here:
https://makerworld.com/en/models/2621183-rescue-box-v2-door-wedge-nitrile-gloves?from=search#profileId-2893179

Boost Me (for free)

Comment & Rating (80)

@user_592346366

Print Profile

Sliding lid with and without eyelet

Great idea. Fits 2 pairs of gloves with a little bit of printing. The lid holds on tight, but you can hear it move if there are no gloves in the box, but it's not a problem

(Edited)

Show original

@Paeddel

Finally THE solution. Unfortunately, the locking doesn't hold 100% because the gloves still press against the lid. Tape helps

The designer has replied

Show original

@GsxRLer

Thank you for the feedback. I will possibly revise the lid

Show original

@3DTF

Boosted

Great job, the boxes are quite useful, I just think the closing system should be more reinforced and hold better, as the lid is very loose, but otherwise it's very good

The designer has replied

Show original

@GsxRLer

Thanks for the feedback. I'll see if I can revise the lid a bit

Show original

@GsxRLer

I have now revised the lid and it fits much better. The closure is also more stable. Feel free to print the lid again and give feedback :)

Show original

@3DTF

Boosted

Replying to @GsxRLer :

It is much better now, the cap closes and is not loose, great job

Show original

@Farti

Boosted

Very cool. It's a shame that the lid cannot be printed separately

The designer has replied

Show original

@GsxRLer

You could just cut up the model and leave the lid

Show original

@Farti

Boosted

Replying to @GsxRLer :

@GsxRLer I can't

Show original

@GsxRLer

Replying to @Farti :

Right-click on the model and then share object. Then you can print the lid separately

Show original

@hsuperprints

Print Profile

Sliding lid with and without eyelet

(Edited)

@TimBasics

Print Profile

Sliding lid with and without eyelet

Very cool for my voluntary ambulance services! Thank you!

The profile uploader has replied

Show original

@GsxRLer

Thank you for the feedback. It’s a shame it wasn’t 5 stars

Show original

@TimBasics

Replying to @GsxRLer :

unfortunately the flap does not hold firm enough and slips out a bit too easily

Show original

@GsxRLer

Replying to @TimBasics :

I have now revised the lid and it fits much better. The closure is also more stable. Feel free to print the lid again and give feedback :)

Show original

@ScottyJ

can you make an A1 mini profile?

@user_2557930496

Boosted

Print Profile

Sliding lid with and without eyelet

Great part, thank you very much. Finally no more searching for hours in the bag and losing half the gloves during use ;D

The profile uploader has replied

Show original

@GsxRLer

That was precisely the idea behind it. I'm very pleased that you like it

Show original

@user_2557930496

Boosted

Replying to @GsxRLer :

I volunteer for the DRK, I suspect my comrades might want something like this too XD

Show original

@c.wilming

Print Profile

Lid glued

I liked it and my comrades liked it

The profile uploader has replied

Show original

@GsxRLer

I am glad. thanks

Show original

@MagicalDR

Print Profile

Sliding lid with and without eyelet

These are great, now added one to work bag and printed a couple for friends.

The profile uploader has replied

@GsxRLer

I am happy to hear that :) have fun with it

Show original

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.