Automaton Model 5

>Θ Assembly Manual:

The last few images in the model display are for assembly reference.
1. Specifications:
- Scale size: 1/10 (height 160mm)
- Internal structure:

  · Print in Place joints: 10 points (10 on torso)

  · Rotational locking tabs: 6 points
- Universal interface: The holes on the waist are 3mm in diameter, compatible with👉Humanoid with [Exoskeleton]

2. Printing essentials:
 - Recommended settings:

   · Nozzle: 0.4mm or 0.2mm

   · Layer height: 0.08mm

 - Material: Default is PLA

   · Other materials such as PETG/TPU have not been tested, scaling tolerances need to be figured out by yourself.

 - Debugging suggestions:

   · It is recommended to print the test pieces from the first plate first.

   · If adhesion occurs, it is recommended to scale the entire model up (scaling ratio is recommended to be within 110%, at which point the joint damping feels best; exceeding this range will cause the joints to be too loose, but will not have other effects).

   · Adjusting the layer height may cause some parts to become rough and difficult to insert and remove. If necessary, it is recommended to scale up the model.

3. Assembly instructions:

 - Joint activation (Print in Place section)

   · Joints such as the shoulders, elbows, hips, knees, and ankles of the model are Print in Place and require manual flexing of the movable parts after removal.

   · Tools can be used to assist (such as needle-nose pliers), normally it will not be damaged unless there is complete adhesion.

 - Limb connection (bayonet structure)

   The upper arm, forearm, and thigh connections use a bayonet structure. When assembling, ensure that the plug lugs align with the hole openings

   · Alignment: Align the plug lugs with the hole openings (at an angle opposite to normal human anatomy)

   · Locking: After insertion, rotate the joint to lock.

 - The wrist uses relatively delicate hemispherical joints. Pay attention to dealing with supports and elephant's foot during assembly.

 - The torso interface is compatible with[Type 6][Curved Sword].

---
☟                        ☟                        ☟
☟                        ☟                        ☟
☟                        ☟                        ☟

>☀ Background Story:
 As a mass-production verification model of humanoid automatons predating Type 6, Type 5's interface expandability and power output were slightly inferior to Type 6 in design. Its status as one of the mainstream models primarily stemmed from the influence of Mikos.
In its early days, Mikos was a model construction area for Durun Federalism. To showcase its dominance, Flo invested heavily in immigrants and resources there... Afterward, the "Angel Crisis" occurred. This military conflict between the Sky Fleet and Moro forced Flo to abandon the Durun Federation plan, leaving the Sky Fleet in chaos, and Mikos consequently fell into anarchy.
A Moro judicial enforcement enterprise seized the opportunity, entering Mikos at an opportune moment with elite forces—a mixed team of humans and humanoid automatons. Leveraging the power of Type 5 humanoid automatons, they managed to establish a foothold locally and founded the "Public Service Company."
To address the issues of insufficient local monetization, difficulty in enforcing commercial contracts, and frequent bloodshed, they decisively adopted an expansion strategy of equity participation rather than acquisition or forced requisition. Furthermore, they dissolved potential hostilities through long-term dividend agreements. This led to an explosive growth in the company's scale, turning all Mikos residents into company shareholders, thus developing the "shareholders are citizens, sovereignty is equity" Mikos model.
The [Type 5] humanoid automatons were also retained and widely used as a symbol of the Public Service Company, becoming common units in Mikos-related armed forces.

---
☟                        ☟                        ☟
☟                        ☟                        ☟
☟                        ☟                        ☟

>✎ Author's Message:
Mecha girls equipped with exoskeletons; these three mecha girls should be considered a series. This blueprint is for the mecha girl body itself; for the exoskeleton parts, please refer to the mecha girl accessories, or click the link to jump to👉Humanoid with [Exoskeleton]

For the author's other works, you can check the author's homepage, or click the links below:

-
Mecha Girl Series—>👉(Chinese)   /   👉(Global)

-
Mecha Girl Accessories—>👉(Chinese)   /   👉(Global)

-

If you believe the author's creations are valuable to you, you can also support the author via👉Afdian (Chinese) or 👉Patreon (Global). Finally, I'm looking for photos of your prints! I'd love to see different colored versions of the mecha girls. It makes me very happy as a creator to see my work in different hands, displaying various colors!