Kevin95

cover

197817fa-6b63-486f-927c-7314b3eebd34.png

6258.jpg

plate_1.png

6259.jpg

<h2>🖨️ Druckprofil Beschreibung</h2><p>Dieses Druckprofil ist speziell für einen präzisen <strong>0,2 mm First-Layer Test</strong> optimiert.</p><p>Es sorgt für eine saubere, gleichmäßige Extrusion mit langsamer Anfangsgeschwindigkeit, um Z-Offset, Haftung und Druckbett-Nivellierung zuverlässig beurteilen zu können.</p><h3>🔧 Profil-Eigenschaften</h3><ul><li>0,2 mm Layerhöhe (einzelne Schicht)</li><li>Reduzierte First-Layer Geschwindigkeit für maximale Genauigkeit</li><li>Optimierte Linienbreite für saubere Flächenabdeckung</li><li>Konstante Extrusion für klare Fehlererkennung</li><li>100 % Infill für eine geschlossene Testfläche</li></ul><h3>🎯 Ziel</h3><p>Dieses Profil hilft dabei:</p><ul><li>Z-Offset exakt einzustellen</li><li>Haftungsprobleme frühzeitig zu erkennen</li><li>Über- oder Unterextrusion sichtbar zu machen</li><li>Unebenheiten im Druckbett sofort zu identifizieren</li></ul><p>&nbsp;</p><p>English version : </p><h2>🖨️ Print Profile Description</h2><p>This print profile is specifically optimized for a precise <strong>0.2 mm first layer test</strong>.</p><p>It ensures clean, consistent extrusion with a reduced first-layer speed, allowing you to reliably evaluate Z-offset, bed leveling, and adhesion performance.</p><h3>🔧 Profile Features</h3><ul><li>0.2 mm layer height (single-layer print)</li><li>Reduced first-layer speed for maximum accuracy</li><li>Optimized line width for full surface coverage</li><li>Consistent extrusion for clear error detection</li><li>100% infill to create a fully closed test surface</li></ul><h3>🎯 Purpose</h3><p>This profile helps you to:</p><ul><li>Fine-tune your Z-offset precisely</li><li>Detect adhesion issues early</li><li>Identify over- or under-extrusion</li><li>Reveal uneven areas on the build plate immediately</li></ul><p>Ideal as a quick calibration print before starting longer or more demanding prints.</p>

<h2>🖨️ Print Profile Description</h2><p>This print profile is specifically optimized for a precise <strong>0.2 mm first layer test</strong>.</p><p>It ensures clean, consistent extrusion with a reduced first-layer speed, allowing you to reliably evaluate Z-offset, bed leveling, and adhesion performance.</p><h3>🔧 Profile Features</h3><ul><li>0.2 mm layer height (single-layer print)</li><li>Reduced first-layer speed for maximum accuracy</li><li>Optimized line width for full surface coverage</li><li>Consistent extrusion for clear error detection</li><li>100% infill to create a fully closed test surface</li></ul><h3>🎯 Purpose</h3><p>This profile helps you to:</p><ul><li>Fine-tune your Z-offset precisely</li><li>Detect adhesion issues early</li><li>Identify over- or under-extrusion</li><li>Reveal uneven areas on the build plate immediately</li></ul><p>Ideal as a quick calibration print before starting longer or more demanding prints.</p>

0.2mm layer, 2 walls, 15% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

<h2>German Version</h2><h2>🧼 0,2 mm Reinigungsplatte &amp; First-Layer Test</h2><p>Diese 0,2 mm dünne Platte eignet sich perfekt zum Testen des First Layers und gleichzeitig zum Reinigen des Druckbetts.</p><h3>🔧 Zweck</h3><ul><li>Kontrolle der <strong>Z-Offset Einstellung</strong></li><li>Überprüfung der <strong>First-Layer Haftung</strong></li><li>Gleichmäßigkeit des Druckbilds testen</li><li>Sanfte Reinigung der Druckoberfläche durch großflächigen Auftrag</li></ul><h3>💡 Anwendung</h3><p>Einfach mit 0,2 mm Layerhöhe drucken (keine weiteren Layer).<br>Die Platte deckt möglichst viel Fläche ab, damit Unebenheiten sofort sichtbar werden.</p><p>Während des Drucks kannst du:</p><ul><li>Linienabstand prüfen</li><li>Über- oder Unterextrusion erkennen</li><li>Zu hohen oder zu niedrigen Z-Offset feststellen</li></ul><p>Nach dem Druck lässt sich die dünne Platte leicht entfernen und nimmt dabei Staub oder feine Rückstände mit auf.</p><h3>⚙️ Empfohlene Einstellungen</h3><ul><li>Layerhöhe: <strong>0,2 mm</strong></li><li>Perimeter: 1–2</li><li>100 % Infill (oder Top/Bottom auf 0, nur eine volle Lage)</li><li>Langsame First-Layer Geschwindigkeit (z. B. 15–25 mm/s)</li></ul><h3>📌 Tipp</h3><p>Wenn die Oberfläche:</p><ul><li><strong>rau und löchrig</strong> wirkt → Z-Offset zu hoch</li><li><strong>stark gequetscht / glänzend</strong> wirkt → Z-Offset zu niedrig</li><li><strong>gleichmäßig matt und geschlossen</strong> ist → Perfekt eingestellt</li></ul><p>&nbsp;</p><p>--------------------------------------------English Version ---------------------------</p><h2>🧼 0.2 mm Cleaning Plate &amp; First Layer Test</h2><p>This 0.2 mm thin plate is perfect for testing your first layer while also helping to clean your print bed.</p><h2>🔧 Purpose</h2><ul><li>Check and fine-tune your Z-offset</li><li>Verify first layer adhesion</li><li>Test overall print surface consistency</li><li>Gently clean the build plate through full-surface extrusion</li></ul><h2>💡 How to Use</h2><p>Simply print at <strong>0.2 mm layer height</strong> (no additional layers).</p><p>The plate is designed to cover as much surface area as possible so that uneven spots become visible immediately.</p><p>During printing, you can:</p><ul><li>Check line spacing</li><li>Detect over- or under-extrusion</li><li>Identify a too high or too low Z-offset</li></ul><p>After printing, the thin sheet can be removed easily and may pick up dust or fine residue from the surface.</p><h2>⚙️ Recommended Settings</h2><ul><li>Layer height: <strong>0.2 mm</strong></li><li>Perimeters: <strong>1–2</strong></li><li>100% infill (or set Top/Bottom layers to 0 to print a single solid layer)</li><li>Slow first-layer speed (e.g., 15–25 mm/s)</li></ul><h2>📌 Tip</h2><p>If the surface looks:</p><ul><li><strong>Rough and patchy</strong> → Z-offset too high</li><li><strong>Over-squished / overly shiny</strong> → Z-offset too low</li><li><strong>Even, matte, and fully closed</strong> → Perfectly adjusted</li></ul><boostme><boosttitle>Boost Me</boosttitle><boostcontent>Thanks for your Support &lt;3</boostcontent></boostme>

<h2>🧼 0.2 mm Cleaning Plate &amp; First Layer Test</h2><p>This 0.2 mm thin plate is perfect for testing your first layer while also helping to clean your print bed.</p><h2>🔧 Purpose</h2><ul><li>Check and fine-tune your Z-offset</li><li>Verify first layer adhesion</li><li>Test overall print surface consistency</li><li>Gently clean the build plate through full-surface extrusion</li></ul><h2>💡 How to Use</h2><p>Simply print at <strong>0.2 mm layer height</strong> (no additional layers).</p><p>The plate is designed to cover as much surface area as possible so that uneven spots become visible immediately.</p><p>During printing, you can:</p><ul><li>Check line spacing</li><li>Detect over- or under-extrusion</li><li>Identify a too high or too low Z-offset</li></ul><p>After printing, the thin sheet can be removed easily and may pick up dust or fine residue from the surface.</p><h2>⚙️ Recommended Settings</h2><ul><li>Layer height: <strong>0.2 mm</strong></li><li>Perimeters: <strong>1–2</strong></li><li>100% infill (or set Top/Bottom layers to 0 to print a single solid layer)</li><li>Slow first-layer speed (e.g., 15–25 mm/s)</li></ul><h2>📌 Tip</h2><p>If the surface looks:</p><ul><li><strong>Rough and patchy</strong> → Z-offset too high</li><li><strong>Over-squished / overly shiny</strong> → Z-offset too low</li><li><strong>Even, matte, and fully closed</strong> → Perfectly adjusted</li></ul><boostme><boosttitle>Boost Me</boosttitle><boostcontent>Thanks for your Support &lt;3</boostcontent></boostme>

Print Profile(1)

Description

🧼 0.2 mm Cleaning Plate & First Layer Test

🔧 Purpose

💡 How to Use

⚙️ Recommended Settings

📌 Tip

Comment & Rating (4)

License

Related Models

0.2mm First Layer Test & Bed Cleaning Plate