Pocket Valentine Rose - Free 3D Print Model

Search models, users, collections, and posts

hyperfixed

Miniatures>Other Miniatures

IP Report

Print Profile(1)

All

A1 mini

H2D

P1S

X1E

H2C

H2S

P2S

X1 Carbon

P1P

H2D Pro

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

13 min

1 plate

4.9(27)

Open in Bambu Studio

Boost

210

528

405

228

Released

Description

The Pocket Valentine Rose is a minimalist, fast-printing token designed to be the perfect "just because" gift. Whether you’re looking for a desk accessory, a small surprise for a loved one, or a way to test out a new filament color, this rose is designed for maximum charm with zero assembly hassle.

Features

No Glue Required: The stem is designed for a perfect friction fit.
Eco-Friendly Design: Uses a small scrap of green filament for the stem—perfect for using up those "end of the roll" pieces!
Fast Print: Optimized for quick production, making it a great "handout" item for Valentine’s Day events.

Assembly Instructions

Print the Rose: Use your favorite red, pink, or white filament.
The Stem: Take a straight piece of 1.75mm green filament. Snip it to your desired length (usually 3-4 inches works best for the "Pocket" look).
Insert: Simply slide the filament into the hole at the base of the rose head.
- Tip: If it’s a bit snug, a quick taper of the filament end with a hobby knife makes it slide right in!

Print Settings

Layer Height: 0.16mm or 0.2mm (0.12mm for extra detail on the petals).
Infill: 10-15% (it’s a light model, so it doesn't need much).
Supports: None! This model is designed to print cleanly without them.

Boost Me (for free)

Looking for a Commercial License? Check out my Patreon

Comment & Rating (43)

@mibaxx

Print Profile

0.2mm layer, 2 walls, 15% infill

Sweet little rose. Looks good in a bouquet with the tulips. 🙂 Scaled to 120% and printed with eSUN PLA at 0.08mm layer height. Top!

(Edited)

Show original

@thenamedane

I need some advice. I just got my A1 and tried printing this. I don't know much about 3d printers, but the print would start messing up either on the first layer, half way through, or towards the end. I searched it up and I'm thinking it's because my build plate wasn't clean enough. First, I printed the boat that comes programmed in it, it did absolutely perfect. I took the boat off with my fingers and my fingers DID touch the build plate. Then, I tried this rose and some other print of a little fox after (from makerworld) and they messed up, unsticking from the plate. Is it because of the oils from my fingers or another problem?

(Edited)

The designer has replied

@hyperfixed

that could definitely be the issue. try washing your build plate with dish soap and water. these are very small so you need good bed adhesion.

@thenamedane

Replying to @hyperfixed :

Ok, do I need some special type of micro fiber cloth/towel, or could I just use like a paper towel?

@hyperfixed

Replying to @thenamedane :

microfiber will work better, but not completely necessary, just make sure there are no towel/papertowel fibers left on the build plate.

@2UglyPpl

Print Profile

0.2mm layer, 2 walls, 15% infill

Very nice and cute rose. When I printed one in Black, I printed it at 0.2 Standard quality, and it was fine, but I knew I could get better detail w higher quality, smaller layers. So I printed the purple ones on High Quality, PLA, all my usual settings, and for some reason, as soon as the file is uploaded from my computer Bambu Studio to my printer (P2S), it swaps my Cooling settings off, and sets it to heating. I had to open the front door and put a fan so that it wouldn't overheat my pla and clog. I have checked all my settings, and I don't know how to stop the from swapping to heating settings on higher quality settings this time.

@HamD3r

My wife did love the treasure hunt. 😃

@HuKo

Print Profile

0.2mm layer, 2 walls, 15% infill

The profile uploader has replied

@hyperfixed

Love the glass!!

@user_3087021711

Print Profile

0.2mm layer, 2 walls, 15% infill

(Edited)

@MakeItWholesome

Boosted

This is SO cute! It's perfect for a pocket-sized gift to be given to anyone for any reason <3

The designer has replied

@hyperfixed

Thanks!

@SNIP3W4TTS

Boosted

Boosted! Nice Model!

The designer has replied

@hyperfixed

Thank you!

@bergbaulive

Print Profile

0.2mm layer, 2 walls, 15% infill

lives super through!

The profile uploader has replied

Show original

@hyperfixed

Awesome!

@jessbran76

Print Profile

0.2mm layer, 2 walls, 15% infill

so cute

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Bouquet of Roses

Golub17

45.6 k

12.8 k

Rose Bear

Kocyns

32.6 k

8.7 k

roses with 5 types of stem ( no support )

Anko

35.3 k

14.8 k

Valentine Rose Box

DM-Designs

4.1 k

2.8 k