Side window ventilation for VW T6.1 - Free 3D Print Model

Search models, users, collections, and posts

Nachozgz

Hobby & DIY>Vehicles

IP Report

Print Profile(1)

All

P2S

H2S

H2C

H2D Pro

H2D

X1 Carbon

P1S

P1P

X1E

X2D

A2L

0.6mm nozzle, 0.3mm layer, 3 walls, 15% infill

Designer

15.5 h

2 plates

4.6(12)

Open in Bambu Studio

Boost

225

751

517

228

Released

Description

Boost Me (for free)

If you find it useful, nice to be boosted! :)

This is a ventilation grille for the side windows of a VW T6.1.

Printed in PETG-HF for durability in water and high temperatures. The file includes versions for both left and right windows. Each window is split into two halves for easier storage. It also has a printed mosquito net, although you may need to add an additional one.

Installation instructions:

- Open the sliding window.

- Install the bottom part on the glass.

- Slide the top part onto it.

- Close the window until it clicks into place. You can press in the center of the model to make it slide more smoothly.

Tested on a VW California Beach T6.1 camper van. If you liked the model, you can buy me a coffee so I can keep buying filament and refining the model ;P

https://buymeacoffee.com/nachozgz

Comment & Rating (51)

@user_3324569578

T6.1 2024

Show original

@Kerswill2002

did you change any settings I’m struggling to print this? keeps warping

@user_3324569578

Replying to @Kerswill2002 :

the settings were not changed. how is your part oriented

Show original

@user_1541478507

Hello, first of all, thank you very much for the file, it's a lot of work, I intend to modify it for my Trafic III and I have a question, the width, I understand that you have created it to fit on the first or second fixture of the window opening, is that right? I'm asking because when I modify it, I want to leave it the same way, because I imagine the distances in the sliding door of the Trafic are not even close. Thank you very much and best regards from Cantabria

The designer has replied

Show original

@user_863529332

Hello That's it It fits with the window open and locks with the first position of the slider I don't know how it goes on the traffic Also it follows the curve of the VW window I don't know if it will be the same on yours Good luck

Show original

@user_3788499396

Hi, I would need them for t6.1, these are a bit short and too wide Could you help me? Thank you

Show original

@user_1541478507

Replying to @user_863529332 :

ok thanks, on the trafic it's shorter and with a chamfer at an angle, but your design already gives me a good base to start. that's what I said thanks for your work

Show original

@user_2751154255

Boosted

I did a test in PLA because I adapted them for my T7 and they came out perfect when I printed them in PETG those ripples came out, I have a Bambu A1, I will look at the settings to see if I can do better

The designer has replied

Show original

@user_863529332

Hello I am sorry I cannot help you I only have the P2S With the profile I have published I have printed several windows in PETG successfully by applying glue stick to the bed for extra security with warping although I am not sure if it is necessary The rest are the default parameters for bambulab filament Thank you for the boost

Show original

@user_3788499396

Hello I would need them for t6.1 these are a bit short and too wide Could you help me? Thank you

Show original

@aldosalomon

Boosted

Hello could you share for the T7? , thanks in advance

Show original

@Kerswill2002

do you have any advice on to print this? I keep having issues

The designer has replied

@user_863529332

Can you detail the problem for me? I have printed 6 with the usual advice for PETG without issues: dry filament and glue stick on the bed to prevent warping. My printer is the P2S

Show original

@Kerswill2002

Replying to @user_863529332 :

it keeps messing up on the corner of the window with weird lines.

@user_863529332

Replying to @Kerswill2002 :

you can remove the strings with a hot air gun or a lighter. I see the lines you're talking about, but I can't help you. It doesn't happen to me. I use the P2S, Bambu Lab PETG HF filament and textured PEI plate. I guess there are more variables like humidity and ambient temperature. The photos I put on the model are how it comes out of my printer. Maybe someone else can help you. Good luck

Show original

@user_5726684

would this fit a T6 please?

@Supasugaman

did you try?

@user_4061588963

Is anyone able to confirm if these would fit T6 Kombi windows?

@Supasugaman

did you try?

@Aux_ence3D

Hello, is this compatible with a T6.1 California Ocean? I want to print it for my van

The designer has replied

Show original

@user_863529332

I have the California Beach T6.1. I assume the windows are the same, but I can't be sure

Show original

@Aux_ence3D

Okay, thank you for answering me ☺️ If I test it, I will keep you updated

Show original

@user_125027469

would you do an adapter for t5? if you need it I'll send you photos and measurements. you would only have to make a piece to fit between these 2

The designer has replied

Show original

@user_863529332

Not for now, I'm sorry

Show original

@user_4293884335

hello I am trying to make one for mine. To be continued

Show original

@user_1131766825

My car is a 6.1 California Beach. I printed the driver's side window, but when I installed it, I found that the height was too much and it didn't fit at all. Are the side windows on the California different sizes?

Show original

@MkoBrk

Hello... I hope you read this... this is supposed to be year-dependent... please reply so I can perhaps help you

Show original

@chabagaming

Greetings, is there something like this for the side windows, driver/passenger? regards

The designer has replied

Show original

@user_863529332

I have seen some, but I did not make the model. I cannot give you the reference, I am sorry. Regards

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.