ARC Raiders - Looting Mk.3 Controller Stand - Free 3D Print Model

Search models, users, collections, and posts

ScarfMeadow

Tools>Gadgets

IP Report

Print Profile(2)

All

X1 Carbon

P1S

H2D Pro

H2C

H2D

A1 mini

X1E

P2S

H2S

P1P

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

6.8 h

7 plates

5.0(32)

0.2mm layer, 2 walls, 15% infill Consolidated Faces & Handle

11.6 h

4 plates

5.0(3)

Open in Bambu Studio

Boost

384

885

613

286

Released

Bill of Materials

Maker's Supply Kits and Parts

Select all

Round Magnet

Bambu Filaments

Select all

Description

UPDATED 20/02/2026: Added the ability to interchange the front panels using magnets. You will need 2x 5mm x 2mm magnets for the stand and 2x 5mm x 2mm magnets for each front panel. Slightly adjusted the tolerances of all panels (front, rear and sides) for better fitting. Addressed some part orientation problems too.

Introduction

ARC Raiders – Looting Mk.3 Controller Stand - Fresh off the printer and ready for action, this controller stand looks like it was scavenged straight from the ARC Raiders universe. Industrial, rugged, and unapologetically cool, it cradles your controller like prized loot after a successful raid. The Mk.3 design brings sharper details, reinforced geometry, and a no-nonsense stance that says “this controller survives the wasteland.”

Built to keep your setup clean and your controller safe, it’s perfectly balanced to hold your gear between sessions—whether you’re grinding missions, showing off your battle station, or just flexing your taste in sci-fi aesthetics.

Loot smarter. Store harder. Display your controller like it actually matters!

Model Details

Easy print and assembly
Suitable for Dual Sense, Dual Sense Edge, Xbox and Xbox Elite controllers.
Interchangeable Survivor, Cautious and Safekeeper front panels available
AMS required
Minimal supports
Super Glue required
8x 5mm x 2mm magnets
Optional 4x 10mmx4mm silicone/rubber feet

This model has been made available to download and print for free with a great deal of time and effort going into designing and presenting it here on MakerWorld. If you enjoyed this model please give generous consideration to leaving a Boost or a Rating — it’s a quick, easy and free way to show appreciation and helps support my work here on MakerWorld. Thanks for checking out my designs!

Boost Me (for free)

Boost here for free!

Comment & Rating (90)

@ShiaMeowBoom232

Boosted

has anyone else had trouble fitting the panels in? they seem slightly too big to fit in correctly.

The designer has replied

@ScarfMeadow

Did you use the latest version of the print profile? It was updated on the 20/02/2026. See update in the description. :)

@ShiaMeowBoom232

Boosted

Replying to @ScarfMeadow :

I printed it today, so I would assume so.

@ShiaMeowBoom232

Boosted

Replying to @ScarfMeadow :

was the size of the main piece updated or the panels? because I printed the main piece a week or 2 ago

@Chaos33

What am I missing? No matter what slicer I use non of the files show what augment it is ???? All 3 i try are blank ?

The designer has replied

@ScarfMeadow

Do you have an AMS? Are you using the print profile?

@Chaos33

Replying to @ScarfMeadow :

yes i have an ams and have tried multiple files listed....

@ScarfMeadow

Replying to @Chaos33 :

You need to open or download the print profile. If you are not using Bambu Studio then download the .3mf file. If you are downloading the raw STL files these will need to be coloured and orientated manually. The STLs are multi part STLs and will need to be converted to parts in your slicer software. Once this is done you will need to manually set the colour for each part. If you don't have experience with this then as I've said it is far easier to download and use the .3mf file where everything is setup for you.

@NeoPanthera

Print Profile

0.2mm layer, 2 walls, 15% infill

Great file, but please check the orientation of the small handles on the front and the side panels in your print profile! both do not lie exactly on the print bed and cause adhesion problems

(Edited)

The profile uploader has replied

Show original

@ScarfMeadow

Hi, thank you for letting me know. Although, you must be using an old print profile as these issues were addressed in an update on the 20/02/2026. Refer to update in the description for more details. Again, thank you for letting me know though! :)

(Edited)

@NeoPanthera

Replying to @ScarfMeadow :

Alright. I downloaded the file beforehand and then printed it recently. I have updated the rating to 5 stars :)

(Edited)

Show original

@CapnShipWright

Boosted

I printed them on smother side with no supports and they print perfectly.

@KCNerdGarage

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed perfectly on the P1S. Another outstanding model! Would love to offer this on my Etsy shop if possible.

The profile uploader has replied

@ScarfMeadow

Hi, yeah go ahead and sell it on ya Etsy store. No commercial licence needed. All I ask is you give proper attribution to me the designer. :)

(Edited)

@KCNerdGarage

Replying to @ScarfMeadow :

I sure will, thank you friend!

(Edited)

@Linski3D

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

I think this print is really neat! it fits my Xbox and PlayStation controllers comfortably. I did add the handles on the front panel to be one piece because I had issues putting the handles into the panel, but no harm no foul. still turned out fantastic!

@user_3870704949

Boosted

Fantastic print !! quick and easy, absolutely no problems printing on my X1C.

@M1ke2kk

Print Profile

0.2mm layer, 2 walls, 15% infill

top

@XYugia

Print Profile

0.2mm layer, 2 walls, 15% infill

Great model, the GameSir controller slides a bit when placed on it, but it's not a big problem (the purple part is painted with metallic paint by myself)

Show original

@HBiC

Print Profile

0.2mm layer, 2 walls, 15% infill

as a noob at Arc Raiders I was excited to finally get myself a remote holder. this came out great however since I have an elite controller with paddles if the controversy is on it can't rest on there when im watching Netflix or the shows fast forward. none the less I ❤️ 😍 💖

@user_1003957163

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill Consolidated Faces & Handle

great design

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.