p2s/x2d poop shoot v.1 - Free 3D Print Model

Search models, users, collections, and posts

Lucky prints

3D Printer>3D Printer Accessories

IP Report

Print Profile(5)

All

P2S

P1S

X1 Carbon

H2S

X2D

H2D Pro

A1 mini

H2C

P1P

H2D

X1E

A2L

new sliding version no holes FYI

Designer

3.9 h

1 plate

4.5(10)

DO NOT PRINT! WILL MOST LIKELY SLIP

Designer

5.1 h

1 plate

4.6(27)

DO NOT PRINT! WILL MOST LIKELY SLIP

Designer

4.7 h

1 plate

4.3(8)

New Sliding - Exhaust Vent Compatible - X2D & P2S

2.4 h

1 plate

5.0(3)

Click to see more

Open in Bambu Studio

Boost

102

436

806

507

Released

Description

I love designing useful and funny models, if you liked this model please consider checking out some of my other models.

for newer version remove the screws above and below the chut and than re-screw once the bracket is in place, ensure not to over-tighten

I HIGHLY RECOMEND THAT YOU CHECK OUT v.2- https://makerworld.com/en/models/2452036-ultimate-p2s-sliding-poop-chute#profileId-2692007 AS IT IS A VASTLY IMPROVED VERSION

I wanted to create a sleek and simple purge shoot that would still work with the external exhaust fan kit, and this is what I came up with.

WHEN USING THE TIGHTER VERSION PRINT IN PETG OR ABS TO PREVENT DEFORMATION

to install simply push in and than up into the purge slide.

Boost Me (for free)

please consider leaving a boost it really helps a lot

external exhaust air filter

compatible

p2s

p2s poop shoot

p2s external exhaust fan compatible poop shoot

Comment & Rating (77)

@ActeonSP

Print Profile

DO NOT PRINT! WILL MOST LIKELY SLIP

The piece came out very well and fits perfectly;). It's just that at the beginning of the overhang, the first layers remained a bit loose. I don't know if supports should be added for that part or if it's already a problem with some parameter in the profile settings. printed with Bambu Lab PLA Matte Black

The profile uploader has replied

Show original

@KINGLLLLLLL

I’m glad you liked it, the overhang also appeared on my part, put I found it minimal enough to not care to much about, If you’d like I can make a profile with support

@ActeonSP

Replying to @KINGLLLLLLL :

Yes, I agree with you I don't see it as a problem I'll keep the part as it was printed If at some point this minor issue can be improved Others will benefit from future downloads Thanks for the design

Show original

@AGGONOIZE

Print Profile

DO NOT PRINT! WILL MOST LIKELY SLIP

Mega, the print came out perfectly! I liked the smoothed version much better and was blown away by how perfectly it came out without supports. I've only printed with resin so far. Thank you so much for the fabulous work! ❤️

Show original

@sku1d

Thanks! I am here to confirm that it also fits with the alternative way to mount the external exhaust fan kit and I printed with a layer height of 0.24 mm, a 0.4 mm HF nozzle, "Infill combination" and the new "Smoothing wall speed along Z (experimental)" feature (= anti-aliasing). The rounded corners feel great, and I'm disappointed that I missed it when the printer printed the long overhang without support. This is really impressive! The fit is good too. One minor improvement could be to add a a lid to attach into the underside of the hole to prevent the bucket from slipping down.

(Edited)

The designer has replied

@KINGLLLLLLL

thank you for the feedback, I will release an updated profile with all of the suggestions, and will also be trying out the anti aliasing.

@user_1813505885

Good print and very good quality with Bambu Petg for my X2D

Show original

@user_939293787

Print Profile

DO NOT PRINT! WILL MOST LIKELY SLIP

Very happy with this print. Fits snuggly on the back of the P2S. Thank you!

@user_2171831378

WHAT THE LIE ITS 60 GRAMS

The designer has replied

@KINGLLLLLLL

my mistake, I believe my first prototype was only 50 grams, I will change it when I have time. Thank you for pointing this out

@user_2171831378

Replying to @KINGLLLLLLL :

BROSKI BRO

@user_2171831378

👍👍👍👍👍👍👍👍👍👍👍👍👍👍😎😎😎😎😎

@user_3168808608

Print Profile

DO NOT PRINT! WILL MOST LIKELY SLIP

(Edited)

The profile uploader has replied

@KINGLLLLLLL

just curious was anything wrong with it

@user_3168808608

I used pla and it cracked when I went to put it in it probably would have been fine if I was carful, it tends to slip down once it gets loaded up I little

@KINGLLLLLLL

Replying to @user_3168808608 :

Ok, I’ll make one that is a little thicker and stronger, thanks for the feedback

@Dominic.Knust

Print Profile

new sliding version no holes FYI

when unhooking the hoses are in the way because the rail is too long otherwise top

The profile uploader has replied

Show original

@KINGLLLLLLL

thank you for the feed back, I may try and design one with shorter rails

@HurstCreations

What about ASA. You think that would work

The designer has replied

@KINGLLLLLLL

I believe it should work although it may be worth scaling it up to match the shrinkage rate, also I would recommend you print the new profile so that exact size and friction created by the plastic doesn't matter.

@user_3830677410

Print Profile

DO NOT PRINT! WILL MOST LIKELY SLIP

Falls off when the printer vibrates.

The profile uploader has replied

@KINGLLLLLLL

when printed in pla it may sometimes slip down when the printer vibrates excessively, I highly recommend that you try my newer model linked in the description, if you’re looking for something smaller than I will most likely be uploading a smaller profile of my v.2 soon

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.