Disney MagicBand Plus 4-Slot Charging Stand - Free 3D Print Model

Search models, users, collections, and posts

jdufkis

Hobby & DIY>Electronics

IP Report

Print Profile(2)

All

H2D Pro

P2S

H2D

X1 Carbon

X1E

P1S

H2S

P1P

H2C

X2D

A2L

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

6.1 h

1 plate

5.0(8)

0.2mm layer, 2 walls, 8% infill

Designer

16 min

1 plate

5.0(2)

Open in Bambu Studio

Boost

320

229

150

Released

Description

Keep your MagicBand+ collection charged, organized, and ready for the parks with this vertical 4-slot charging stand.

This stand is designed to hold up to four Disney MagicBand+ bands at once in a compact vertical layout, keeping cables clean and your bands easy to grab. Each band slides into its own slot and stays aligned while charging so nothing ends up tangled or scattered across your counter.

The stand is designed specifically around a 4-port USB-A hub so everything plugs into one clean power source instead of four separate wall adapters. It creates a single neat charging station for your whole family or group.

Important hub note:
This stand is designed for use with the USB-A version of the 4-port hub shown in the photos. The USB-C version of this hub will not charge MagicBand+ bands even though it looks identical. The USB-A version does charge properly and works great for this setup.
Link: https://a.co/d/0SIR7Rb

This makes a perfect countertop or hotel room charging solution for Disney trips and keeps everything tidy between park days.

⭐ If you found this helpful or love the design, please give it a boost and share your make. It really helps support more Disney themed creations.

Features

Holds and charges up to 4 MagicBand+ bands
Vertical layout saves counter space
Keeps bands aligned while charging
Designed for USB-A 4-port hub
Clean cable management inside the stand
Perfect for Disney trips and daily storage

Comment & Rating (36)

@user_2991458023

Loved the print for my MagicBands! I wanted more of an end cap, so I made something up pretty quick to top it off! thanks!!

The designer has replied

@jdufkis

Nice!

@Sienar

Print Profile

0.2mm layer, 2 walls, 15% infill

The profile uploader has replied

@jdufkis

Awesome!

(Edited)

@King_Harold

I really like this. Is there any way you could make it for 5?

The designer has replied

@jdufkis

The problem with 5 is then it's too tall to print unless you have a H2 series printer. I can add one though .

@King_Harold

Replying to @jdufkis :

Got ya. Nevermind then. We have an A1 so I’m sure it would be too tall unless it’s modular.

@jdufkis

Replying to @King_Harold :

Yeah I have an A1 and this is getting close to the top already, its like 240mm high. You could cut it in the slicer but you'd lose strength. I have an idea though. I'll model some stuff up and see what I can come up with to get 5 or 6 on one stand. Will have to either add a 2nd hub or find a different one.

@Rohii_3D

Will this print on the A1 mini?

The designer has replied

@jdufkis

No A1 its like 240mm tall, I am working on finishing one that can be printed on the A1 mini, I'll post the link here once I finish it.

@Rohii_3D

Replying to @jdufkis :

Thanks!

@jdufkis

Replying to @Rohii_3D :

https://makerworld.com/en/models/2736698-disney-magicband-charger-4-band-a1-mini#profileId-3034065

@Sienar

Print Profile

0.2mm layer, 2 walls, 8% infill

(Edited)

@eurias

I used the same usb hub and I can’t get the chargers connected to it, there is no room to plug them in

The designer has replied

@jdufkis

you need to run the cables out the bottom of the stand, then plug them into the hub and then slide the hub into the stand.

@eurias

yeah, I was able to get them in after some tries. My concern now is that the way the cables are bent it will put a lot of stress into them

@jdufkis

Replying to @eurias :

Mine have been fine, and I take them in and out for trying different designs.

@user_4061858863

anyone seen an endcap for this one i have tried others and they dont fit

The designer has replied

@jdufkis

I am working on one for you now, the test print is on the printer now.

@jdufkis

Replying to @jdufkis :

I just uploaded a profile with a cap.

@user_713418029

this doesn’t work. it clamps the charging cords too much which will damage the cords quickly. need more room for cables.

The designer has replied

@jdufkis

I've been using it a ton and there's not an issue and I take mine in and out all the time for designing and such.

@user_233222134

Print Profile

0.2mm layer, 2 walls, 15% infill

worked great! super excited to use this on my cruise with the fam where space and outlets are at a premium.

@user_3011236637

do you have an end cap file for the top to make it look clean?

The designer has replied

@jdufkis

I just posted a profile for it.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.