1 Liter Water Bottle Cup Holder Adapter - Free 3D Print Model

Search models, users, collections, and posts

Jason and a bunch of wires

Hobby & DIY>Vehicles

IP Report

Print Profile(2)

All

X1 Carbon

P2S

X2D

P1P

A1 mini

P1S

H2D

H2S

X1E

H2D Pro

H2C

A2L

Full Height Cup Holder

Designer

8.5 h

2 plates

5.0(14)

Shorty Profile

Designer

7.7 h

2 plates

5.0(2)

Open in Bambu Studio

Boost

202

211

132

Released

Bill of Materials

Bambu Filaments

Select all

Description

The Cup Holder Revolution has begun! Just published the next evolution in this lineup. Before you print the original, go have a peek at Holdeez!

Hot on the heels of the Half Gallon Jug Cup Holder Adapter, I had a request for one better sized for a 1L bottle of water. The request was specifically based around Waiakea brand water, but this will also accommodate Fiji and Smartwater. Fortunately I had a few minutes last night before the snow got going to run out to Wawa and pickup a bottle to test with. LOL

Probably a bunch of other brands work too, though I haven't exactly had the time to do an exhaustive test.

4 plates in the profile, 1 each for PLA, PETG, ASA, and ABS. If you've got another material type in mind, there really isn't anything material-specific here, so feel free to give it a go. As was the case with the half-gallon, there are modifier blocks to slow down printing of the side lattice, ensuring those bits turn out nice and smooth! Please don't delete them. Yes, it increases the print time by a bit, but hey - it's not a race. :)

Sample print shown here was done in eSun's PLA Basic. I highly recommend printing in something that will withstand the heat of a hot car in the summer, like PETG, ABS, ASA, PCTG, etc.

Boost Me (for free)

Thank you all for your kindness, Likes, Downloads, Makes, and Boosts. Your likes, makes, boosts, and downloads help fund my supply of filaments, parts that gets used in prints, as well as consumables and various spare parts. Thank you so much for your support!

Membership

If you'd care to offer some additional support, please consider becoming a member at the Tip Jar (or higher) level. Thank you! If you’re interested in a commercial license to sell my prints, please have a look at the commercial plan offered here.

Join

Comment & Rating (35)

@qwentastic2

Print Profile

Full Height Cup Holder

love it

The profile uploader has replied

@jcandthewires

That pink looks great!

@qwentastic2

Replying to @jcandthewires :

Thank you so much.

@user_774366862

Print Profile

Full Height Cup Holder

Absolutely love it! I printed both the tall and shorty, both fit in our cars perfectly. Love the design, it is easy to print. Printed the tall white in PETG and the shorty in Rainbow Silk which won't be staying in the car for obvious reasons, I'll use that in my office.

@swelker

Print Profile

Full Height Cup Holder

printed both the standard and shorty and both turned out great. Gave them out as gifts and everyone has loved them

@swelker

do you have the shorty version of the 1L like the 1/2 gallon?

The designer has replied

@jcandthewires

Not yet but give me a bit. I'll try to put something out today.

@swelker

Replying to @jcandthewires :

awesome thank you

@jcandthewires

Replying to @swelker :

Had a little time before I had to head out, so I'm about to upload. Check back in a little bit!

@fatmac

Print Profile

Full Height Cup Holder

@user_2869858842

where is the bottom?

The designer has replied

@jcandthewires

Bottom of what? It’s a single piece.

@user_2869858842

Replying to @jcandthewires :

would like to see a picture looking into the crate. can you store stuff in the cup area or not?

@jcandthewires

Replying to @jcandthewires :

Sure you can. Same as the half gallon one I’ve got posted. It’s just an open box sized for the various vessels. I’ve actually got a test print of a 1-gallon version running on the A1 right now!

@user_1526950331

what did you use for supports? i love the file, it's one of the better ones i have found. I am kind of new to this and supports on this one is a learning curve.

The designer has replied

@jcandthewires

Normal, manual with snug as the style. I do 3 interface layers with a 0.275mm z-height. They pop right off that way.

@cjones2

can you release a pint sized one for lile small tea cartons on choc milk?

The designer has replied

@jcandthewires

I'm happy to take a stab - can you give me the measurements of the carton you're interested in (preferably in mm)? I think there are also a handful of other ones out there in that really small size if you'd rather just print & go.

@Rico_3D

any chance you can make one for a 2L bottle of Soda?

The designer has replied

@jcandthewires

My exhaustive research (ie 30 seconds of googling, lol - I don't have any 2L bottles in the house) suggests that the diameter of that should be 110mm, which should JUST fit in the half gallon one, as it's using 110mm sides. Might be a little tight. Let me know!

@user_2418180663

Print Profile

Shorty Profile

awesome print

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under the MakerWorld Exclusive License.

You may create derivative works based on this object, provided that all such derivative works are published exclusively on the MakerWorld platform and include proper attribution to the original creator. You may not share, upload, host, distribute, or publish this object—or any derivative work of this object—on any other digital platform, marketplace, or distribution channel. Commercial use of this object and any derivative works is strictly prohibited. This includes, but is not limited to, selling, renting, sublicensing, or using the object in any context in which you receive monetary compensation or other financial benefits.