DIN SCUBA Regulator & DIN SCUBA Tank Dust Caps

============= BREAK NOTICE =========================

Hello 3D printing friends!

Due to work requirements, studies and home renovations we will be little to not active on MakerWorld for the next coming weeks. Should there be remarks / feedback that you would like to share and would love to see implemented in our work or certain models, please send us a DM as those will be much easier to find and read after coming back. General comments etc on models tend to get buried which is unfortunate and is something we would like to avoid as we take your feedback seriously.

We apologize for any inconvenience our absence might cause but rest assured all messages will be addressed upon our return to designing!

Cheers!

====================================================

DIN SCUBA Regulator & DIN SCUBA Tank Dust Caps with optional lanyard attachment!

SCUBA Diver enthusiasts! Introducing a new model :)

One that is widely available for purchasing but this is our take on it.

Meet the DIN regulator and DIN Tank dust caps either with a diving flag print or as a solid color.

Additionally available either with or without a lanyard attachment (more on that in a little bit).

These dust caps are designed for the type DIN  (Deutsches Institut für Normung) which is arguably the most common standard of dive equipment in Europe but is also available outside of it. Our equipment uses this standard, hense we designed them around this :)

Dust caps are quite a common piece of accessory to help keep dust, sand and salt out of your expensive equipment but often fall flat due to their basic design. Another pesky problem dust caps often have is that an attached lanyard will twist up and get tangled due to their design.

NO MORE! Our dust cap come with a lanyard attachment that continuously rotate to prevent just that :)

There are 4 print profiles available. Allow us to quickly explain so you can pick to right one for you!

DIN REG Dust Cap:

Standard Dust cap for DIN regulators. Choose between a Dive flag print or solid color

DIN REG Dust Cap + Lanyard Attachment

Dust cap for DIN regulators with rotating lanyard attachment. Choose between a Dive flag print or solid color

DIN TANK Dust Cap:

Standard Dust cap for DIN tanks. Choose between a Dive flag print or solid color

DIN TANK Dust Cap + Lanyard Attachment

Dust cap for DIN tanks with rotating lanyard attachment. Choose between a Dive flag print or solid color

Compatible with all Bambu printers: X series, P series, H series. A1 and A1 mini.

Instructions

• Select the profile you need: Regulator or Tank and then with or without lanyard attachment
• Dive Flag prints require the use of an AMS
• Print per object to ensure better adhesion and results (NOT ACTIVATED BY DEFAULT FOR PRINTER COMPATIBILITY)

Assembly for lanyard attachments

NOTE: The dust cap has an extruded cut in the hole which will allow the lanyard attachment to rotate

Place the attachment with the ring upwards on a solid surface. Then press the dust cap with moderate force onto the attachment.

Moderate force is required! But do not go all HULK on it ;)

Tips

• When using in tropical conditions, make sure to use suitable filament that can withstand heat and salt water exposure.
• These lanyard dust caps can also act as fun keychains attachments!
• Dust cap ARE NEVER 100% waterproof and are NOT an excuse to leave your equipment submerged. We do not take any responsibility for damaged equipment.
• Don't want to many lanyards on your equipment? That is OK! The thread fit into each other. So take the dust cap of your reg and screw it onto the dust cap of the tank! Done and done!

Print Settings (recommended)

• No supports needed
• 0,16 mm optimal settings
• Print per object advised on the dustcap with lanyard attachments (NOT ACTIVATED BY DEFAULT TO ENSURE PRINTER COMPATIBILITY)
•  

For more scuba diving themed accessories, please check out the images below (Click on image):

If you like the model, please consider leaving a like and a rating with pictures of your makes! It is encouraging to see my creations out there.

Also consider leaving feedback regarding the models as it will help improve my overall skills as a beginner 3D designer!

Want to support me with some coffee? :)