Ball Joint Handle Pre-Assembled BoneBag Remix 3.0

The Ultimate BoneBag Remix 3.0 is here, still prints PRE-ASSEMBLED, and now has a Ball-Joint Handle! This fantastic improvement allows the handle to swing out of the way, allowing easy access to the contents of your bag!

As always, break free from the limitations of the original! No more breaking during assembly, or falling apart after a few days of light use! Ever since my v2.0 Remix* The joints are now encapsulated and stronger than the original! That means they cannot be detached, but they shouldn't ever fail due to light  wear and tear either! It can even be printed in PLA Silk! The new redesign, since v2.0,* features an increased capacity for storage at the bottom level as the obstructing bone that was needlessly at the bottom has been trimmed out to only exist externally. *Improved “tail” bone that not only looks much better, but will print WITHOUT failure AND help keep your small items from falling out! There are now also additional small ribs that will assist in retaining your small items. *The handle features a redesign now having the classic tried and true dovetail grove connecting it. I printed the handle sub-optimally in regards to structural strength of the dovetail in PLA Silk, in an arch position, and it easily handled heavy abuse while carrying 20lbs/9.09kgs of steel weights! The handle is compatible with the original design. *Last but not least, there is now a protruding housing near the top that can house 10mm x 3mm round magnets to function as a clasp! No longer will the top just simply flop open exposing your precious cargo to loss or theft! This model has the same improved, very strong, collar bone that I have already posted which is compatible with the original design.

Key features in list format:

-A NEW Ball-joint handle that can swivel to the side, out of your way!

-All of the other features you may know and love from my Remix 2.0!

If you have not yet seen the original post for this design by @鸦鸦101 / @yaya_101, please make sure you stop over there to pay tribute by Liking and Downloading to give them the points they deserve!

The support must be removed VERY carefully! Do not rush or force the sides open or apart until the supports are sufficiently removed! I suggest using needle-nose pliers. I suggest grabbing the top of the support and twisting the needle nose pliers clockwise and counter-clockwise to wiggle the supports loose without using too much force. Disconnect as many as you possibly can from any-and-all angles before removing large chunks! I even used the tip of the needle-nose pliers to stab in between the ribs to push them into the chest cavity to help with detaching them if there was not enough room to grab the branches. Experiences and results may vary depending on the size of the needle-nose pliers you use. There may of course be better tools at your disposal!

This is best printed in PETG or ASA as they can handle day to day use better than other filaments, but it can be printed in absolutely any filament on the market for the first time! Reinforced fiber filament were featured on a YouTuber's video where he made the original model; but you shouldn't use such filaments on something you will handle daily with your bare hands as you run the risk of getting those fibers in your skin, and then on your face, in your eyes, and in your body via your hands…

Optional Assembly:

If you are only printing the swivel handle to replace the handle on a BoneBag that you already own, please refer to these instructions. The connection points may require filing down the dovetails joints if there is any sagging or deformation of the geometry. The handle and connectors must be assembled as pictured below.

LEGAL NOTICE: This model is NOT included in any Commercial License you may purchase from the original creator @鸦鸦101 / @yaya_101 or anyone else. A Remix is partially owned by the original creator and partially owned by the individual that remixed it. In order to sell this model, you would have to pay out royalties to both parties. If you have merely purchased a Commercial License from @鸦鸦101 / @yaya_101, you cannot sell this model. The same applies for any Remix you may come across on the internet.

Suggestions for Ratings and Reviews:

Please take a moment to write why you are rating the value you choose, especially if less than 5 stars. This not only helps any creator improve a design to further benefit your future use, but also helps fellow consumers make their own determinations and modifications where necessary. A mere standalone rating of less than 5-star helps no one, as no one is aware as to why you are displeased and where the shortcoming is. It may even help you better understand your printer and how to utilize it as an issue may often lie with the preparations you have made or failed to make.