PiShock Modular Storage and Charging Bay

Most of the Measurements are based on the official PiShock Products. Compatibility with similar Products depends on the sizing. For the Shocker and the Straps it shouldnt matter too much but in Terms of the Spacers, the sizing is wildly different so please check that before you print specific parts.

This is a modular System designed for Storage of the various PiShock Parts and to make charging of the PiShocks more structured. It includes Storage Parts for Spacers, the PiShocks itself, the Straps, the Hub, and fully assembled PiShocks (Strap,Spacer,PiShock). All Parts are connectable via small Inserts on all four edges and cable Holder Parts for the charging cables are included. It also includes a removal Help I will go into detail now for the connecting mechanism:

• 1: The Connector itself

  

• 2: The Holes for the Connectors on each Part

  

• 3: Lining up of the Connector Piece and the Holes on two Parts

  

The Connector System is designed in such a way that every Part can connect to every other Part, so the combination and structure is up to the use case and the desired look. Now some details to the different Parts/Plates:

1. Pi_Shock_Charging_Raw_Slanted: This is the Charging Hub for a single PiShock without accessories as a slanted Version.
2. Connectors: The universal Connector used in the whole System
   1. The Connectors can be quite stiff on the first Insert but the Parts and the connectors are able to withstand some force. In the next Plates is also a removing Help to make removing stuck connectors a bit easier.
3. Pi_Shock_Charging_Raw_Straight: This is the Charging Hub for a single PiShock without accessories as a flat Version.
4. Pi_Shock_Charging_Strap_Straight: This is the Charging Hub for a single PiShock with a Strap.
   1. The following Part will Help to keep the PiShock in Place, since the Strap makes it quite side heavy.

5. Pi_Shock_Charging_Strap_Addon: This is a Addon for Pi_Shock_Charging_Strap_Straight. You attach it to one of the sides and then Slide the strap through it as seen in this picture:

   

6. Connector_Remover_Help: This a simple Removing Helper to make removing of stuck connectors easier. Attach it to the one side and wiggle until the connector comes out
7. Pi_Shock_Cable_Holder_Single: This a cable holder for the charging cables. Overall these are designed to fit for cables up to 5mm in Diameter. 

   1. This Part is made out of two parts that attach to each other. One Side has a smaller connector, which fits to the smaller Piece that keeps the cable in the hole (as an example the Dual Version):

      

      

8. Pi_Shock_Cable_Holder_Dual: Cable Holder for 2 Cables
9. Pi_Shock_Cable_Holder_Quad: Cable Holder for 4 Cables
10. Pi_Shock_Cable_Holder_Okto: Cable Holder for 8 Cables
11. Pi_Shock_Complete_Storage: This is the Storage for a complete PiShock, so Strap + Spacer + PiShock
    1. All Storage Modules can be stacked on each other
    2. To store it just curl up the PiShock as shown on the Model Pictures
12. Pi_Shock_Strap_Storage: This is the Storage for one Strap:
    1. To store it just curl up the Strap as shown on the Model Pictures
13. Pi_Shock_Shocker_Storage: This is the Storage for two Shockers
14. Pi_Shock_Hub_and_Spacer_Storage: This is the Storage for two Spacers and the Hub itself.

I have tried to keep it as modular as possible and include pretty much all parts that could be needed. If they are any suggestions for other Parts or Improvements, I will be happy to add them. Also if they is anything not clear in this Description, feel free to comment^^