r4nd0m

cover

CleanShot 2025-12-01 at 10.02.54@2x.png

IMG_7613.JPG

IMG_7612.JPG

IMG_7878.JPG

plate_1.png

2025-12-01_87ebb35ae0aec.png

The settings should be included but make sure to use supports:• 0.2mm layer height• print with supports (I have used tree auto, 30 degrees)&nbsp;

0.2mm layer, 2 walls, 10% infill

Rasalghul

Screenshot 2025-12-10 160100.png

Screenshot 2025-12-10 160116.png

20251211_022724.jpg

20251211_031023.jpg

20251211_031039.jpg

Das originale Modell ist hervorragend und absolut zufriedenstellend. Die folgenden Anpassungen wurden nicht vorgenommen, um Fehler zu korrigieren, sondern lediglich, um das Modell für Magnum- und grössere Flaschen als 0.7dl noch stabiler zu machen, besonders, weil ich es zusätzlich leicht vergrössert habe.<h3>Anpassungen &amp; Gründe</h3><ul><li>Wandlinien 2 → 3 (optional) → Mehr Stabilität im Hals- und Schulterbereich für schwerere Flaschen.</li><li>Fülldichte 10% → 15% (Gyroid) → Verstärkte innere Struktur ohne viel Mehrmaterial.</li><li>Reduzierte Wandgeschwindigkeit (Aussenwand 150 mm/s, Innenwand 250 mm/s) → Sauberere Details und weniger Vibrationen am Geweih.</li><li>Optimierte Stützen (XY-Abstand 0.30 mm, obere Schnittstelle 0.3 mm) → Sicherer Halt an Ohren und Geweih, trotzdem gut lösbar.</li><li>Elefantenfusskompensation 0.05 mm → Saubere und stabile Auflagefläche.</li><li>Reinigungsturm deaktiviert → Nicht nötig beim einfarbigen Druck.</li></ul>Diese Anpassungen erhöhen hauptsächlich die Tragfähigkeit für grosse Flaschen, während das ursprüngliche Design und die Qualität vollständig erhalten bleiben. The original model is excellent and extremely satisfying as it is. These adjustments were not made to fix anything, but simply to adapt the model for Magnum and larger bottles, especially since I slightly increased its size. The goal was to improve stability while keeping the original design fully intact.  <h3>Adjustments &amp; Reasons</h3><ul><li>Wall count: 2 → 3 (optional) → Increases stability in the neck and shoulder area to support heavier bottles.</li><li>Infill density: 10% → 15% (Gyroid) → Strengthens the internal structure without adding much extra material.</li><li>Reduced wall printing speed (Outer wall 150 mm/s, inner wall 250 mm/s) → Cleaner details and fewer vibrations around the antlers.</li><li>Optimized supports (XY distance 0.30 mm, top interface 0.3 mm) → Better support for ears and antlers, still easy to remove.</li><li>Elephant foot compensation: 0.05 mm → Ensures a clean and stable bottom surface.</li><li>Disabled purge tower → Not needed for single-color printing.</li></ul>These adjustments mainly increase the load-bearing capacity for larger bottles while keeping the excellent original design and quality completely intact.

The original model is excellent and extremely satisfying as it is. These adjustments were not made to fix anything, but simply to adapt the model for Magnum and larger bottles, especially since I slightly increased its size. The goal was to improve stability while keeping the original design fully intact.  <h3>Adjustments &amp; Reasons</h3><ul><li>Wall count: 2 → 3 (optional) → Increases stability in the neck and shoulder area to support heavier bottles.</li><li>Infill density: 10% → 15% (Gyroid) → Strengthens the internal structure without adding much extra material.</li><li>Reduced wall printing speed (Outer wall 150 mm/s, inner wall 250 mm/s) → Cleaner details and fewer vibrations around the antlers.</li><li>Optimized supports (XY distance 0.30 mm, top interface 0.3 mm) → Better support for ears and antlers, still easy to remove.</li><li>Elephant foot compensation: 0.05 mm → Ensures a clean and stable bottom surface.</li><li>Disabled purge tower → Not needed for single-color printing.</li></ul>These adjustments mainly increase the load-bearing capacity for larger bottles while keeping the excellent original design and quality completely intact.

0.18mm layer, 2 walls, 15% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

My wife wanted a champagne bottle holder for the festive season and this is the result after quite a few attempts. I had to print and correct it numerous time to make sure champagne bottles of different sizes fit as well as wine bottles. You can fit 2 on the same build plate if you wish to print a pair as shown in the pictures/&nbsp;MY wife is happy, I am happy with the results so hopefully you will too.&nbsp;If you do like it, please leave a comment, drop me a like or if you feel generous please boost my model - thank you.&nbsp;It prints well in Bambu Labs Silver and Gold but you can obviously print it in your colour of choice.

Print Profile(2)

Bill of Materials

Description

Comment & Rating (44)

License