P2S pop chute right side - Free 3D Print Model

Search models, users, collections, and posts

Rafal_Simple_Design

3D Printer>3D Printer Accessories

IP Report

GIF

Print Profile(6)

All

P2S

X1 Carbon

H2D

H2S

P1S

P1P

X1E

H2C

H2D Pro

X2D

A2L

A1 mini

NEW VERSION, PLA, 0.2mm layer, 3 walls, 20% infill

Designer

3.5 h

1 plate

4.7(17)

PLA, 0.2mm layer, 3 walls, 20% infill

Designer

1.1 h

1 plate

5.0(6)

PLA, 0.2mm layer, 3 walls, 40% infill

Designer

1.6 h

1 plate

4.5(6)

PLA, 0.2mm layer, 3 walls, 40% infill

Designer

3.3 h

1 plate

4.3(6)

Click to see more

Open in Bambu Studio

Boost

328

387

227

Released

Description

3D model

P2S pop chute right side

You need:

8x magnets 6x3mm

2x heat inserts M3x5 (or shorter)

2x M3x10 screws

Can be printed with PLA, PETG or any other

NOTE:

A new version of CHUTE has been added.

Poops fall into the container more easily.

No blockage of poops.

Comment & Rating (48)

@HoagieDesigns

Nice poops chute! I actually did not add the mounting hardware. I printed it with support tree, and the little bit of interference with the power cord of my P1S is enough to hold it into place 😎

(Edited)

@user_3041679061

whats the point of the mount hardware? Are you meant to screw the pount to the P2S and the magnets to the shoot?

@HoagieDesigns

Replying to @user_3041679061 :

The uploader's picture 11/15 shows the mount screwed to the chute, with the magnets glued into the mounting to make it stick to the P1S's metal enclosure.

@Spugno

Print Profile

NEW VERSION, PLA, 0.2mm layer, 3 walls, 20% infill

Ok, the print is not perfect

Show original

@user_2988462185

Print Profile

NEW VERSION, PLA, 0.2mm layer, 3 walls, 20% infill

one of the few projects on this site, thanks

@Bast13n

Print Profile

NEW VERSION, PLA, 0.2mm layer, 3 walls, 20% infill

super impression

@Kryzbar

Boosted

Print Profile

PLA, 0.2mm layer, 3 walls, 40% infill

it's good but it's need improvement. slide and container need some reduction for better fit . when I want to sweep poops from slide container disconnect and I got poop on my table

@AG1209

Boosted

Print Profile

NEW VERSION, PLA, 0.2mm layer, 3 walls, 20% infill

Printing went smoothly and turned out perfectly Most chutes go to the left, so the selection was rather limited I chose this design because the chute is as steep as technically feasible It has been in use for about 30 hours now. However, waste often remains at the bottom of the chute (in front of the bin) Therefore, you have to manually push the accumulated waste the rest of the way into the bin from time to time. Not a problem for me Despite PLA, nothing has stuck anywhere so far. PLA, PETG-HF, and ABS were tested Material: Bambu PLA Matte Color: Nardo Grey The color is very similar to that of the P2S

(Edited)

Show original

@AG1209

Boosted

Print Profile

PLA, 0.2mm layer, 3 walls, 40% infill

Printing went smoothly and turned out perfectly It also holds a decent amount of waste Material: Bambu Nardo Grey Color is very similar to that of the P2S

Show original

@Ca4door4u

Print Profile

PLA, 0.2mm layer, 3 walls, 40% infill

prints great

@KassMeOutside

is there a way to make one smaller bin version? they are all very large

The designer has replied

@RafalZie3Design

sure, just sketch what you need

@KassMeOutside

Replying to @RafalZie3Design :

Could you make one that is 55 mm wide and 180 mm long? and it can be a “small version” thank you!!

(Edited)

@RafalZie3Design

Replying to @KassMeOutside :

done, please check

@mpd2l17

where is the file for the chute?

The designer has replied

@RafalZie3Design

which one? con4 aleady added

@mpd2l17

I see it now thanks

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.