Search models, users, collections, and posts

fingerboard Flat rail - tech deck

ceratarges
Toys & Games>Other Toys & Games
IP Report

Print Profile(1)

All
A1
X1 Carbon
P2S
P1S
X1
H2D
H2D Pro
H2C
P1P
X1E
H2S
X2D
A2L
0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
1 h
1 plate
4.6(27)
Open in Bambu Studio
Boost
228
402
32
3
939
652
Released 

Description

A clean, minimalist flat bar designed for fingerboard tricks. The pieces lock together you don't need glue. If it is too tight you can rescale a little but for me works fine. 
 

To optimize the fit and increase assembly clearance, I recommend using thermal expansion to your advantage: chill the rails in a freezer and preheat the base. This ensures a perfect press-fit that's secure enough to eliminate the need for adhesive.
 

 

Boost Me (for free)

Boost me if you like it



No supports.

 


Wait until the print has completely cooled down, then press the rail into the base. The tolerances are very tight, so it’s designed to fit by friction and doesn’t require any glue — though you can modify it if you prefer.

 

fingerboard
fingerboard
fingerboard
finger board
rail
skatepark
grind
grind rail
flat rail
tech
Deck

Comment & Rating (32)

(0/1000)
@Derkhan
Print Profile
0.2mm layer, 2 walls, 15% infill
peices dont fit the holes. Will shave down and glue.
The profile uploader has replied
0
Reply
@ceratarges
cool male part, warm female and it will fit perfect. when temperature will be equal you even don't need a glue
0
Reply
@zyphizoid
Replying to @ceratarges :
ayo?
0
Reply
@user_1382272594
Print Profile
0.2mm layer, 2 walls, 15% infill
its good but hard to assemble does not go in good
0
Reply
@user_3233488285
had to remove the support in the middle because it holds otherwise everything is okay
Show original
0
Reply
@user_2895331728
Print Profile
0.2mm layer, 2 walls, 15% infill
tolerances were too tight
0
Reply
@user_2374741165
Print Profile
0.2mm layer, 2 walls, 15% infill
slides around,but it doesn’t matter that much
0
Reply
@Cloughie
Print Profile
0.2mm layer, 2 walls, 15% infill
so good I printed it again
0
Reply
@user_1634567283
Print Profile
0.2mm layer, 2 walls, 15% infill
Other Issues:it was th wrong size could not fit
The profile uploader has replied
0
Reply
@ceratarges
@user_1634567283 As you can see in the pictures, it’s fit! :) Tolerances are enough if it is printed correctly. In the description, you'll also find a tip on how to assemble it easily and painlessly. What’s more, the components fit together even without any cooling or heating
0
Reply
@user_2452803620
Print Profile
0.2mm layer, 2 walls, 15% infill
Other Issues:had to cut off parts where the railing goes into the base because the sqeeze was too tight! Otherwise nice model!
The profile uploader has replied
0
Reply
@ceratarges
Thank you for your comment! A good trick is to chill the male part in the freezer. It makes the pieces fit together easier, and you get a perfect fit once they warm back up.
0
Reply
@Syafiqmatthew
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
@kegy.com
Print Profile
0.2mm layer, 2 walls, 15% infill
(Edited)
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Fingerboard Skateboard
Fingerboard Skateboard
DR3D_Prints
12 k
2.7 k
Pokemon Deck Box
Pokemon Deck Box
jbogusz
13.4 k
4.1 k
Steam Deck Stand V2
Steam Deck Stand V2
revoun
9.1 k
1.3 k
MTG Card Deck Box
MTG Card Deck Box
Ian Smith Builds
10 k
1.6 k