mynameisbuddy

cover

Machollo Pic 1.JPG

Quappo Pic 1.JPG

5.JPG

8.JPG

1 - Kopie (2).JPG

1 - Kopie.JPG

1.JPG

4 - Kopie.JPG

4.JPG

5 - Kopie.JPG

8 - Kopie.JPG

Abra Pic 1.JPG

Georok Pic 1.JPG

Kleinstein Pic 1.JPG

Quaputzi Pic 1.JPG

Pokemon Shop Logo.jpg

plate_1.png

plate_2.png

plate_3.png

Pic 1.png

Pic 2.png

Pic 3.png

Pic 4.png

2025-10-06_80a925589c575.jpg

Print Profile:  <h2>Quality</h2>Layer Height<ul><li>Layer height: 0.09 mm</li><li>First layer height: 0.20 mm</li></ul>Line Width<ul><li>Default: 0.42 mm</li><li>First layer: 0.50 mm</li><li>External perimeter: 0.42 mm</li><li>Internal perimeter: 0.45 mm</li><li>Top surface: 0.42 mm</li><li>Infill: 0.45 mm</li><li>Internal solid infill: 0.42 mm</li><li>Supports: 0.42 mm</li></ul>Smoothing / Walls / Advanced<ul><li>Smoothing type: None</li><li>Wall generator: Classic</li><li>Wall order: Inside → Outside</li><li>Print infill before walls: Off</li><li>Bridge flow ratio: 1.0</li><li>Thick bridges: Off</li><li>“Single wall on top surfaces”: All surfaces</li><li>(Precise Z-height appears Off in the shot)  </li></ul><h2>Strength</h2>Walls<ul><li>Perimeters: 2</li><li>Detect thin walls: On</li></ul>Top/Bottom<ul><li>Top surface pattern: Monotonic</li><li>Top shell layers: 5</li><li>Top shell thickness: 0.60 mm</li><li>Top color layers: 5</li><li>Bottom surface pattern: Monotonic</li><li>Bottom shell layers: 5</li><li>Bottom shell thickness: 0.00 mm (as shown)</li><li>Bottom color layers: 5</li><li>Internal solid infill pattern: Straight lines</li></ul>Infill<ul><li>Infill density: 5%</li><li>Infill pattern: Grid</li><li>Infill anchor length: 400 (UI shows “mm or %”; value = 400)</li><li>Max infill anchor length: 20 (“mm or %”; value = 20)</li></ul>Advanced (Infill)<ul><li>Infill/perimeter overlap: 15%</li><li>Infill angle: 45°</li><li>Bridge angle: 10°</li><li>Minimum area for infill: 15 mm²</li><li>Combine infill: Off</li><li>Detect narrow internal solid infill: On  </li></ul><h2>Speed</h2>First Layer<ul><li>First layer speed: 50 mm/s</li><li>First-layer infill speed: 105 mm/s</li></ul>Other Layers<ul><li>External perimeter: 60 mm/s</li><li>Internal perimeter: 150 mm/s</li><li>Small perimeters: 50% (relative)</li><li>Small-perimeter threshold: 0 mm</li><li>Infill: 180 mm/s</li><li>Internal solid infill: 180 mm/s</li><li>Vertical shell speed: 80% (relative)</li><li>Top surface: 150 mm/s</li></ul>Overhang Slowdown<ul><li>Enable slowdown on overhangs: On<ul><li>10% overhang: 60 mm/s</li><li>25%: 30 mm/s</li><li>50%: 10 mm/s</li><li>75%: 10 mm/s</li><li>100%: 10 mm/s</li></ul></li><li>Slowdown by height: Off</li></ul>Bridges / Gap fill / Support<ul><li>Bridge speed: 50 mm/s</li><li>Gap fill speed: 180 mm/s</li><li>Supports: 75 mm/s</li><li>Support-interface speed: 40 mm/s</li></ul>Travel<ul><li>Travel speed: 350 mm/s</li></ul>Acceleration<ul><li>Normal printing: 400 mm/s²</li><li>Travel: 10 000 mm/s²</li><li>Movement accel (first layer): 6 000 mm/s²</li><li>First layer (print accel): 500 mm/s²</li><li>External perimeter: 200 mm/s²</li><li>Internal perimeter: 0 mm/s² (as shown)</li><li>Top surface: 2 000 mm/s²</li><li>Infill: 100% (relative)  </li></ul><h2>Supports</h2>General<ul><li>Enable supports: On</li><li>Type: Tree (auto)</li><li>Style: Organic tree</li><li>Overhang threshold angle: 20°</li><li>On build plate only: On</li><li>Support only critical regions: Off</li><li>Remove small overhangs: On</li></ul>Raft<ul><li>Raft layers: 0</li></ul>Support Material<ul><li>Support/raft base: Standard</li><li>Support/raft interface: Standard</li></ul>Advanced<ul><li>First layer density: 90%</li><li>First layer expansion: –1 mm</li><li>Support wall loops: –1</li><li>Top Z-gap: 0.15 mm</li><li>Bottom Z-gap: 0.15 mm</li><li>Base pattern: Rectilinear</li><li>Base pattern spacing: 2.5 mm</li><li>Base pattern angle: 0°</li><li>Top interface layers: 2</li><li>Interface pattern: Straight lines</li><li>Top interface spacing: 0 mm</li><li>Normal support expansion: 0 mm</li><li>Support/Model XY gap: 0.35 mm</li><li>Support/Model first-layer gap: 0.20 mm</li><li>Max bridge length: 0 mm</li><li>Independent support layer height: Off</li></ul>Tree Supports<ul><li>Branch distance: 5 mm</li><li>Branch diameter: 2 mm</li><li>Branch angle: 25°</li><li>Branch taper angle: 5°  </li></ul><h2>Other (Misc)</h2>Bed Adhesion<ul><li>Skirt loops: 0</li><li>Skirt height: 1 layer</li><li>Brim type: Automatic</li><li>Brim width: 10 mm</li><li>Gap between brim and object: 0.10 mm</li></ul>Wipe Tower (Purge Tower)<ul><li>Enable: ✅ On</li><li>Skip points: ✅ On</li><li>Inner ribbing: Off</li><li>Tower width: 35 mm</li><li>Max tower speed: 90 mm/s</li><li>Tower brim width: 3 mm</li><li>(Field “Füllungsrate/Füllung …”: value shown 10 – likely 10%)</li><li>Fill gap: 100%</li><li>Ribbed wall: Off</li></ul>Nozzle Cleaning Options<ul><li>Clean nozzle in object infill: Off</li><li>Clean nozzle in object supports: ✅ On</li></ul>Special Modes<ul><li>Slicing mode: Regular</li><li>Print sequence: By layer</li><li>Spiral vase: Off</li><li>Timelapse: Traditional</li><li>Fuzzy skin: None</li></ul>Advanced Settings<ul><li>Use interlock structures: Off</li><li>Interlock depth (segmented area): 0 mm</li></ul>G-code Output<ul><li>Reduce retraction during infill: ✅ On</li></ul>&nbsp;

0.09mm layer, 2 walls, 5% infill, advanced speed

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

IMPORTANT!! You can open all Pokémon at once directly in Bambu Studio, OR you can download all Pokémon (.3mf) INDIVIDUALLY.Click on “Download STL/CAD Files”. There you can download all the individual MULTICOLOR - Projects (.3mf). This bundle contains: Poliwhirl, Poliwrath, Abra, Kadabra, Alakazam, Machop, Machoke, Machamp, Bellsprout, Weepinbell, Victreebel, Tentacool, Tentacruel, Geodude, Graveler<boostme><boosttitle>Boost Me</boosttitle><boostcontent>Boost to Catch ´Em All!</boostcontent></boostme>!!! Pokémon Gen 1 – Multicolor 3MF FilesREADY TO PRINT! :DI hand-textured all 150 Pokémon (+3 Specials) and put them in cool fighting poses – here’s the fith batch.&nbsp;Enjoy your prints &amp; happy collecting!A like or boost keeps me motivated to share more. ;)

Multicolor Pokemon 061 to 075 (Gen 1)

ASIA

Print Profile(1)

Description

Comment & Rating (0)

License

Related Models