TomTom Rider Sun Visor 4xx 5xx - Free 3D Print Model

Search models, users, collections, and posts

Captain_Orange

Hobby & DIY>Vehicles

IP Report

Print Profile(1)

All

X1 Carbon

P2S

H2S

X1E

A1 mini

H2C

P1P

X2D

H2D

H2D Pro

P1S

A2L

0.2mm layer, 3 walls, 20% infill

Designer

2.2 h

1 plate

4.9(11)

Open in Bambu Studio

Boost

176

117

Released

Description

Content has been automatically translated.

Show original

Boost Me (for free)

If you like my model, please leave a like and a Boost

Sun visor for TomTom Rider models of the 400 and 500 series

The sun visor is simply slipped over the device from the front and holds itself in place due to its precise fit

Material choice: UV and heat resistant (I generally use ASA for outdoor use)

motorcycle accessories

Comment & Rating (34)

@HuguesC

A few years ago I bought an expensive one from a major motorcycle equipment manufacturer which was relatively expensive and not as good as this one Everything is there: button access, water drainage at the bottom of the screen Thank you for this great product

The designer has replied

Show original

@Captain_Orange

Glad you like the sun visor, and thank you for the feedback

Show original

@Yulock

Hello unfortunately it always only prints a narrow frame No sun protection What is the problem here Regards Uwe

The designer has replied

Show original

@Captain_Orange

Hello Uwe I'm sorry It works perfectly for me and so far I haven't received any similar reports Please re-upload the file to your Bambu Studio and try again Maybe something went wrong during the download You haven't changed anything in the slicer settings

Show original

@Yulock

Hello, nothing changed, it won't print anymore. See picture. strange printed from the phone I'll load it into the Slicer tomorrow

Show original

@Yulock

Replying to @Captain_Orange :

Well, even after slicing in Bambu Studio, it's just a small frame. I'll take a different model then

Show original

@Jordanj20

Boosted

Print Profile

0.2mm layer, 3 walls, 20% infill

super

(Edited)

The profile uploader has replied

@Captain_Orange

Thank you very much for the extremely kind comment. I will look into it and correct it if necessary

Show original

@Captain_Orange

Hello again I just downloaded the 3mf from Makerworld and supports were/are definitely activated. Mistakes can happen, but the mistake is not mine or my uploaded file. Therefore, I do not find the choice of words and the 2-star rating justified.

Show original

@Jordanj20

Boosted

everything is fine in the 3mf you "downloaded" as written nothing is activated when started remotely via mobile app I didn't remove the supports before I took a photo 😄 at that moment it was a complete disaster when I entered the room... don't read too much between the lines I've done it again and think it will work

Show original

@Sushi78

Print Profile

0.2mm layer, 3 walls, 20% infill

Nice model but supports are not enabled in de profile. My P1S managed get a decent print without supports but it definetly need supports for the best result.

The profile uploader has replied

@Captain_Orange

Thank you for the feedback. I have just checked the profile and the wrong supports were indeed activated. I accidentally selected manual supports. I have fixed this problem immediately and activated the automatic supports. Sorry, it was my mistake

Show original

@user_3058512531

Boosted

Perfect! Thank you!

The designer has replied

@Captain_Orange

Thank you for the boosts and have fun with the aperture

Show original

@user_223334337

Print Profile

0.2mm layer, 3 walls, 20% infill

Exactly

The profile uploader has replied

Show original

@Captain_Orange

Vielen Dank!

@user_3416874694

Print Profile

0.2mm layer, 3 walls, 20% infill

Perfect fit for my TomTom Rider. Nice print. Thanks

The profile uploader has replied

Show original

@Captain_Orange

Nice to meet you Thank you very much for the rating

Show original

@user_238920837

Print Profile

0.2mm layer, 3 walls, 20% infill

past perfect

@GDR46

Print Profile

0.2mm layer, 3 walls, 20% infill

The profile uploader has replied

@Captain_Orange

Vielen Dank!

@tonigri

Print Profile

0.2mm layer, 3 walls, 20% infill

The profile uploader has replied

@Captain_Orange

Vielen Dank!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.