Dual Samsung Galaxy Watch Charging Stand Dock - Free 3D Print Model

Search models, users, collections, and posts

Zouz

Hobby & DIY>Electronics

IP Report

Print Profile(1)

All

X1 Carbon

P1P

X1E

P2S

A1 mini

H2D Pro

H2D

H2S

P1S

H2C

X2D

A2L

0.16mm layer, 2 walls, 15% infill

Designer

2.1 h

2 plates

4.8(24)

Open in Bambu Studio

Boost

135

389

543

349

Released

Description

Dual Samsung Galaxy Watch Charging Stand Dock. This stand is made to perfectly fit the official Samsung Galaxy Watch charging pad, holding it in place while giving your watch a stylish resting spot. I've also added a built-in cable routing channel lets you guide the charging cable in the direction you want, reducing clutter and keeping your desk or nightstand clean.

Designed with practicality and stability in mind, the dock ensures your watch sits at a comfortable viewing angle while charging, so you can easily check the time, battery level, or notifications at a glance.

This version is an branch from my single watch dock below, created for those who require two docks in one.

Note:

The charging pad will need to be pushed in place once you've put the cable through, it it quite tight to reduce breakage.
Supports are required for this version due to it's orientation on the print bed.
No AMS required, two plates setup in the 3mf file, one for the stand and the other for the colored insert if you wish to use it.
This fits the 30mm Samsung watch charger only.

Single version:

https://makerworld.com/en/models/1765650-samsung-galaxy-watch-charging-stand-dock-no-ams

Boost Me (for free)

If you would like to encourage me to keep uploading my models, feel free to boost.

Comment & Rating (37)

@M787

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

I think a 95-97 scale would be optimal

Show original

@user_2389038108

Which galaxy watch chargers did they come with? it sounded like newer fast chargers are hair smaller

@M787

Boosted

Replying to @user_2389038108 :

Both watch 8 and watch 5 chargers I had to secure with adhesive pads because there is too much play The chargers for both watches are exactly the same size

(Edited)

Show original

@user_2389038108

Replying to @M787 :

Is yours printed in 100% scale?

(Edited)

@kai10sushi

Print Profile

0.16mm layer, 2 walls, 15% infill

had to print twice cause i saw the comments saying it was loose/needed to be scaled down, but when i did, the charger didn't fit at all. maybe others have a different charger, but the official Samsung Galaxy watch charger fits perfectly at 100% scale. thanks for this!

The profile uploader has replied

@Superzuz

thanks :) they could have different tolerances or untried filament maybe!

(Edited)

@kai10sushi

Replying to @Superzuz :

oh yeah, there's probably that too. anw, cheers!

@Fernandes360

Everything is fine, thank you very much

Show original

@Cornalist

It fit perfectly thanks

Show original

@LGMan

this worked out great for my wife's and my phone.

@Cornalist

Print Profile

0.16mm layer, 2 walls, 15% infill

@user_1294570922

Great design but did not fit my official Samsung charger or aftermarket charger. In both cases. The print is too small. Print with caution.

(Edited)

The designer has replied

@Superzuz

Hi, I made this to fit my Samsung charger that came with my Galaxy Watch 5. May be a filament issue as I've had a few comments where it fit perfect and others that had slightly too big issue! If you need to tailor to your filament, consider printing at a slightly larger size.

@user_1294570922

No worries, I just thought it may be a helpful comment with all of the "too big" comments. Still a great design and I was able to fix with a Dremel tool. In my case I have chargers for watch 4, 5 and watch 7.

(Edited)

@user_1426838269

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

at 100% size the holes are bit to large, but a little bit of dualsided tape fixed it

@nwiegard

Print Profile

0.16mm layer, 2 walls, 15% infill

Super, thank you very much

Show original

@lefourbedu31

As a beginner in 3D printing, how can I change the dimensions to fit the charger which is 33.5 mm and not 29mm? Thank you very much in advance :)

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.