Hat Stand with Gridfinity Base - Free 3D Print Model

Search models, users, collections, and posts

gerrit

Fashion>Other Fashion Models

IP Report

Print Profile(1)

All

P1S

H2D

P1P

H2S

H2D Pro

X1 Carbon

X1E

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

4.4 h

1 plate

4.8(18)

Open in Bambu Studio

Boost

203

569

578

324

Released

Description

Organize your baseball caps with this Gridfinity-compatible hat stand that holds up to 6 baseball caps. Built with the standard Gridfinity baseplate footprint, it integrates directly into your existing setup.

Stores 6 baseball caps neatly in angled slots

⚠️ Please note: This stand is designed for curved-brim baseball caps. It is not compatible with flat-brim hats.

Angled design keeps hats from slipping and aligns brims cleanly
Gridfinity-compatible base – locks into your modular system
Geometric honeycomb sides for a modern look and reduced filament use
Great for desks, closets, or display shelves
Strong, single-piece print – no assembly needed

Perfect for hat collectors, everyday wearers, and Gridfinity enthusiasts who want a clean, modular storage solution.

Recommended Print Settings:

Material: PLA or PETG
Layer Height: 0.2 mm
Infill: 15–20%
Supports: Not required
Bed Adhesion: Standard

Note: This design is intended for longer-term storage and display. Because the hats are stacked at an angle, pulling a single hat from the middle may cause others to shift. I prioritized maximum storage capacity (6 hats) over quick grab-and-go access.

baseball hat organizer

Comment & Rating (28)

@gonzo345

Pinned by Designer

Print Profile

0.2mm layer, 2 walls, 15% infill

Nice and useful design! Many many thanks!

The profile uploader has replied

@gerritbutler

You're the first to share a pic of anything I've put up on this site! Its so cool seeing my design out in the wild. I hope you like it. Its can be a little weird getting used to the angles at first, but I now use mine without even thinking about it. Even the tricky middle slots are easy to access now. Enjoy!

(Edited)

@user_3599338003

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

Awesome print.

(Edited)

@SSAAOO

Print Profile

0.2mm layer, 2 walls, 15% infill

The profile uploader has replied

@gerritbutler

Awesome! Glad it worked out for you!

@user_3701241538

Print Profile

0.2mm layer, 2 walls, 15% infill

The profile uploader has replied

@gerritbutler

I appreciate the rating! If you don’t mind my asking, what could be changed to make it a 5 star print?

@user_3701241538

Replying to @gerritbutler :

It is realy a great design and good print. Having a mounting point on the bottom to allow it to go from sitting on a self to being mounted on the wall was the only thing I would suggest. But again a great item

@gerritbutler

Replying to @user_3701241538 :

I completely agree. I have regretted not having multiple versions for a while now. I need to make a flat version without gridfinity. It'll save filament and a ton of time for those who want that. And then I could do keyholes for mounting on the wall. The main reason I havent done it yet is because this was one of my first 'complicated' Fusion designs and the file is a mess. I was learning a lot at the time. I'm taking some time off soon and I have a backlog of stuff I have been wanting to design for a while now. I'll make sure to revist this design during that time. I appriciate the compliments and the feedback.