Search models, users, collections, and posts

Bicycle chain cleaner (MTB,road bike,gravel bike).

Remixed by

Print Profile(1)

All
A1
X1E
P1P
X1 Carbon
X1
A1 mini
H2D
P1S
H2D Pro
H2S
P2S
H2C
X2D
A2L

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
1.8 h
1 plate
4.4(9)

Open in Bambu Studio
Boost
168
513
17
2
337
188
Released 

Description

Content has been automatically translated.
Show original

ENGLISH:

This bike chain cleaner is based on the model: https://makerworld.com/it/models/796445-bike-chain-cleaner-toothbrush-version?from=search#profileId-769393;

I added a handle to make it easier to hold during cleaning so that it can be used from above or below without any problems.

No screws are needed for fastening, as it consists of two separate pieces that are held together with simple connectors (if you intend to close it permanently, you can also use glue); I only used three Oral B Classic Care toothbrushes:

immagine spazzolini

(cut about 16 cm from the bottom as shown in the photo), which, having made the model quite narrow, can be inserted and remain stuck in place.

There is a hole at the top, and by drilling the brush with a Ø3mm or Ø2.5mm drill bit, you can insert the nozzle of the degreaser and pour some in from there.

Printed in PLA, it has not caused any problems with degreaser and other chemicals. I have tested it a couple of times and the chain is very clean and performs well.

I hope you find it useful and, if so:

Boost Me (for free)

Teo.

 

 

ITALIANO:

This bike chain cleaner is based on the model: https://makerworld.com/it/models/796445-bike-chain-cleaner-toothbrush-version?from=search#profileId-769393;

I added a handle to make it easier to hold during cleaning so that it can be used from above or below without any problems.

No screws are needed for fastening, as it consists of two separate pieces that are held together with simple connectors (if you intend to close it permanently, you can also use glue); I only used three Oral B Classic Care toothbrushes:

toothbrush image

(cut about 16 cm from the bottom as shown in the photo), which, having made the model quite narrow, can be inserted and remain stuck in place

There is a hole at the top, and by drilling the brush with a Ø3mm or Ø2.5mm drill bit, you can insert the nozzle of the degreaser and pour some in from there.

Printed in PLA, it has not caused any problems with degreaser and other chemicals. I have tested it a couple of times and the chain is very clean and performs well.

I hope you find it useful and, if so:

Boost Me (for free)

Teo

Comment & Rating (17)

(0/1000)

Print Profile
0.16mm layer, 2 walls, 15% infill
didn’t fit the toothbrush, but if it was bigger this is a great print!
The profile uploader has replied
profile
1
Reply
Hello thank you for the feedback, I had made the model quite tight so that the toothbrushes would not come out (I don't know if it also works with other brands of toothbrushes)
Show original
0
Reply
very good!! congratz!!
The designer has replied
Show original
designer
1
Reply
Grazie!!
0
Reply
Great top! thanks
The designer has replied
Show original
designer
1
Reply
Grazie a te!
0
Reply
Great Excellent remix
The designer has replied
Show original
designer
1
Reply
Grazie mille!!
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
It would be amazing if there was a water hole to clean the brushes
profile
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Great, thank you!
profile
1
Reply
Good mod adding the handle. If you add the new oil/greasing 3d print then it becomes a chain cleaning kit.
(Edited)
designer
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
profile
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
profile
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
profile
1
Reply