Buds 3 Pro charging holder for Tesla Model 3/Y - Free 3D Print Model

Search models, users, collections, and posts

3D_COSMO

Hobby & DIY>Vehicles

IP Report

Print Profile(1)

All

P1P

H2D

X1E

X1 Carbon

A1 mini

P1S

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

2.3 h

3 plates

4.7(11)

Open in Bambu Studio

Boost

106

344

261

185

Released

Description

This model is created specifically for the Tesla Model Y and Model 3 before the facelift. If you have the newer models, I’d love to hear if it fits!

There are three options to choose from: a blank design, one with the Tesla logo, and another with the Tesla font.

I recommend using PETG for printing, but PLA will work nicely too! Just a quick note—I'm a little concerned it might bend in the summer heat.

Happy printing!

tesla model 3 accessories

tesla model 3 highland

Comment & Rating (19)

@samsvremail

Printed with standard settings on an X1c using Ziro brand red pla (I won't have to use it often in my car so pla will be fine). I have a 2024 Model 3 (highland) and can confirm it fits and works perfectly. you can see the charging light in this picture. thank you so much for this it's perfect.

@kabliga

it's a good model and a good print and it looks nice. but the Juniper refresh it does not fit. it hits the hump in the middle of the charging pad which lifts it up. it still holds the buds for the most part in the correct place but I find it shifting sometimes and not charging anymore. and sometimes on a bumpy road because it's lifted up it will completely slide out of position. good make, wish it would work for me.

@RedwingsDK

Print Profile

0.2mm layer, 2 walls, 15% infill

Came out very nice

@IceyA

Print Profile

0.2mm layer, 2 walls, 15% infill

Other Issues:it sits too low so my tmy 2025 (not juniper) doesnt seem to let it charge, i have to hold it above the stand for about 10 seconds and 0.5mm above it and the let it rest after charge has started

The profile uploader has replied

@user_1340218601

Sorry to hear that! You are the first to complain. I will upload another set which will sit appr. 5mm higher. (I hope that "0,5mm" is a typo from your side:) )

@IceyA

Replying to @user_1340218601 :

yea 5mm ish i have not measured, i can do that later tonight 😅

@IceyA

missing 5mm and can u make for juniper aswell?

@user_2928154189

This is the only one I have found that actually sits almost flush in the charging spot. Would love if these fit Gen 3 airpods.

@RGrocoski

Print Profile

0.2mm layer, 2 walls, 15% infill

perfect

@SRBSandzak

Hello, Thank you for the very nice model I'm getting the juniper soon I'll let you know if it fits is it possible to have a model with the Tesla lettering and logo fully extruded with an empty Tesla to see through If it's available I'll boost it immediately :)

(Edited)

Show original

@samsvremail

I'll be printing this tonight when I get home and I'll let you know how this works in the refreshed model 3.

@user_3892284417

Print Profile

0.2mm layer, 2 walls, 15% infill

@Rallg

Print Profile

0.2mm layer, 2 walls, 15% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.