Toxic Slime Cube Miniature - RPG - Toy - Wargaming

Thank you all for your support. I'm always happy to hear your opinions and suggestions for new models. So please share them in the comments.

You can offer me a coffee and support my work here >>> https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support. The website also includes a commercial license that allows you to sell all my existing models.

https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support.

Toxic CUBE Slime Miniature – FDM 3D Print (D&D Ready) 
"From the depths of the dungeon oozes a wrath that clings to bone and steel..."

Bring your tabletop battles to life with this high-detail Toxic Slime miniature! Whether you're running a boss encounter or surprising your players with a corrupted ooze in a forgotten sewer, this model is both functional and visually striking.

Toxic CUBE Slime

 Actions:

Acidic Slam. Melee Weapon Attack: +5 to hit, reach 5 ft., one target.
Hit: 13 (2d8 + 4) acid damage. Non-magical armor or weapons hit by this attack must succeed on a DC 13 Constitution saving throw or take a permanent -1 to AC/damage.

Corrosive Aura (Recharge 5–6).
All creatures within 10 ft. must succeed on a DC 14 Constitution saving throw or take 3d6 acid damage and have disadvantage on Strength checks for 1 minute (as gear starts corroding).

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

•  

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support