MV agusta air brake LEFT ducati hyper-899-701 - Free 3D Print Model

Search models, users, collections, and posts

MARCOPOSSENTE

Hobby & DIY>Vehicles

IP Report

Print Profile(1)

All

A1 mini

P1P

H2D

P1S

X1E

X1 Carbon

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill Left sinistro

Designer

2.1 h

1 plate

5.0(1)

Open in Bambu Studio

Boost

113

163

Released

Description

Content has been automatically translated.

Show original

AIR DUCTS FOR MV AGUSTA FIT ALL MV MODELS THAT HAVE THE SAME FRONT END AS THE RIVALE 800 AS SHOWN IN THE PHOTOS HERE YOU WILL FIND THE RIGHT AND LEFT SIDES JUST REMOVE THE CALIPER SLIDE IT ON AND PUT A ZIP TIE ON THE FRONT PART A user also mounted it on a Ducati Hypermotard which has the same fork caliper and foot as the MV Agusta

some users told me that it is also compatible with Ducati HYPERMOTARD 950 DUCATI PANIGALE 899 and with Husqvarna 701 look at the photos

Comment & Rating (14)

@user_18362507

GREAT JOB THEY ARE VERY WELL ASSEMBLED ..ON A FRIEND'S RVE

The designer has replied

Show original

@user_18362507

MARCOPOSSENTE ,,, IS THERE A POSSIBILITY FOR A HYPERMOTARD 950 SP WHICH HAS OLLINS SUSPENSION ..IT'S JUST THAT WITH THE ONES WE'VE TESTED THEY ARE TOO TIGHT ON THE CALIPER THAT'S WHY IT RUBS TOO MUCH TO ENTER AND THE CLEARANCE OF THE DIAMETER TO ADJUST IT A LITTLE MORE , OR WOULD YOU PROVIDE ME WITH THE FILE SO I CAN MODIFY IT TO BE ABLE TO PRINT IT?? , I AM WAITING A GREETING.

Show original

@MARCOPOSSENTE

thank you, if you can send me more photos if you have a boost it's much appreciated

Show original

@user_18362507

Replying to @MARCOPOSSENTE :

I do not have tokens to send you the boost .... if I had I would but I don't. Regarding what I wrote to you, can you tell me something? Could you send me the original model, clearly not STL, so I can make the modifications for my SP that has an Öhlins fork

Show original

@Eples

Amazing work! Thank you so much.

The designer has replied

@MARCOPOSSENTE

I am pleased that you like it

Show original

@user_3655224739

Great design and great work I have revised it a bit and printed it with ASA after 3 test prints with pla I was then able to finish printing the parts with ASA filament and I love it they fit perfectly on my MV Agusta Brutale ❤️

The designer has replied

Show original

@MARCOPOSSENTE

thank you , I'm glad you liked them . if you can send me a boost

Show original

@user_2729927480

I printed this and installed it on a Hypermotard 821 and an Mv Agusta F3. It turned out very well, however, when tightening the brake caliper on the 821, the support cracked because the wall is very thin

Show original

@3DiRane

What material do you recommend

The designer has replied

Show original

@MARCOPOSSENTE

PLA, economical and prints well, and for what it needs to do, it's fine. During assembly, remember the front strap. I made them in PLA for my BMW, and I've already driven 4000km with them and haven't had any problems

Show original

@lancerromero28

Replying to @MARCOPOSSENTE :

it doesn't heat up even when driving hard?

@MARCOPOSSENTE

Replying to @lancerromero28 :

print them as you believe

Show original

@user_585276496

Print Profile

0.2mm layer, 2 walls, 15% infill Left sinistro

Thankyou

No more

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.