Bicycle Gyro Can holder - Free 3D Print Model

Search models, users, collections, and posts

paulinex3d

Hobby & DIY>Sport & Outdoors

IP Report

GIF

Print Profile(1)

All

X1 Carbon

P1P

H2D

X1E

P1S

H2D Pro

H2S

P2S

H2C

X2D

A2L

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

3.6 h

1 plate

4.4(37)

Open in Bambu Studio

Boost

1301

3354

1.8 k

961

Released

Description

This is a bicycle handlebar-mounted gyro with suspension system that keeps your drink perfectly upright - even over rocks and little drops! By combining a two-axis gyro with a miniaturized spring‐damped suspension, it isolates the can or cup from every bump and twist on rough roads. There are 3 models attached, each of which is print in place with minimal support. There are also 2 models with different diameters of bicycle handlebars, however each diameter was increased by 6mm to glue the rubber to it for a stronger grip with the handlebars.

I tested this gyro on trails and forest paths and it was a pretty successful experience, however it fits best in an urban environment, and it looks like a very technological and modern addition to your bike. It is most suitable for hot summer days and nice, active rides!

Comment & Rating (74)

@user_1139452354

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

Printed great. can’t wait to try this!

(Edited)

@mattrbll

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

I put it on the motorcycle and it broke

Show original

@paulinex3d

Bro I think that is not supposed to be on motorcycle

(Edited)

@mattrbll

Replying to @paulinex3d :

Yep! That could be the problem. I need something like that, but for a motorcycle. Thanks.

(Edited)

@UlyssesCain

try a stronger filament

(Edited)

@user_2260196944

Boosted

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

Genuinely hilarious, was not expecting this to work as well as it does. Printed mine in some PLA-CF to improve stiffness as I was worried about the inner parts coming out under load.

@user_503778562

Boosted

how did the PLA-CF work in comparison, I’m wondering if I should get some first

@user_2260196944

Boosted

Replying to @user_503778562 :

Honestly I think you'd be fine with regular PLA, maybe up the wall count and top and bottom surface thickness if you want to improve stiffness a bit. If I was going to print it again I'd maybe use some of the Tinmorry PETG-GF I have on hand but that stuff is hardly any more expensive than regular PLA.

@user_503778562

Boosted

Replying to @user_2260196944 :

ok, thanks for replying

@TomaT3

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

Printed out without problems.

@user_2584503870

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

@NNIAS

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

Thought I missed something, after reading and looking around it turns out you need too zip them with tierips..... Well that on is on me. Nice solid print.

@PurrPlexed

Print Profile

22.5mm Holder, 0.2mm layer, 2 walls, 15% infill, Arachne

Strength Issue:Broke after 1 small bump

@user_2828788403

can I buy you’re bike

The designer has replied

@paulinex3d

you sure can! https://cults3d.com/:3291706

@fatcat3D

yeah he’s got a hella good bike

@everettpursell

Replying to @fatcat3D :

I know and if it rear suspension that would be even crazier

@dmt98

Printing through mobile app or through Bambu studio I noticed the spring has missing geometry and not able to get it to print correctly. Preparing the print everything looks fine but when slicing the print that’s when the geometry goes missing on the spring walls

@dmt98

Might need to be a higher resolution for it to print correctly. I’ve noticed when I simply the model more, more holes are made

@Lildude2012

I had the same issue with both sizes.

@HayMoon

Set Wall generator to Arachne and the spring should print fine with a .4 nozzle

@user_503778562

Boosted

can you include somthing on how to put it together?

The designer has replied

@user_503778562

Boosted

I boosted you twice, please reply

@paulinex3d

I will try but the only difficult part is to slide gyro thing into the frame, you just need to put frame part into the space in gyro and than rotate it to fix in place.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

4 Ring Gyro Fidget

CRASH_3D

99 k

13.3 k

Spray Can Holder

CitySideGig

5.6 k

3 k

Cooler Can Holder (std 12oz can)

animuL67

25.4 k

6.7 k

GIF

Two in one gyro fidget toy V2

Zonique2k

10.2 k

1.8 k