Search models, users, collections, and posts

IKEA TROFAST to STOKKE TRIPP TRAPP Adapters

EOD_LAB
Household>Other House Models
IP Report

Print Profile(1)

All
A1
P1P
P2S
X1E
A1 mini
H2D Pro
X1
H2S
H2D
P1S
X1 Carbon
H2C
X2D
A2L
0.2mm layer, 6 walls, 25% infill
0.2mm layer, 6 walls, 25% infill
Designer
2 h
1 plate
4.7(3)
Open in Bambu Studio
Boost
27
111
11
4
237
148
Released 

Description

Content has been automatically translated.
Show original

Adapters for Trofast Ikea drawers on Stokke Tripp Trapp. I designed these supports from scratch because the ones I found had too much play or were weak. They are printed in PETG, with a 0.20 strength profile, adjusted supports to minimize scarring, 6 wall loops, and 25% infill

(Note: I have created another optimized version on my profile with less text and logo extrusion, an Ultra Strength print profile that increases infill to 30% and uses honeycomb infill, all without increasing print time or filament)

stokke adaptor
stokke
trofast
tripp trapp
IKEA

Comment & Rating (11)

(0/1000)
@user_2696457483
Boosted
Perfect fit compared to a couple of other models I've tried that are a little loose and wobble. This attaches to the chair leg perfectly and supports having a lid on. I'd say the only downside is the supports are hard to remove and ended up leaving strands that I needed to use a knife to cut off. The embossed words (whilst handy) and logo in particular left bits in the gaps that needed some time to cut out. I think the only improvement I can think of is to reduce the embossed use, maybe just have L and R embossed instead. Edit: Also not sure if Stokke has changed the dimensions of their chair so for reference we purchased our chair late 2024
(Edited)
The designer has replied
designer
2
Reply
@EOD_LAB
Thank you very much for your comments on the model and your constructive observations. I made changes in the mentioned areas and reduced them to "L" and "R" and extruded the logo. I optimized the infill to 30% honeycomb, and the type of support interface to make it easier to remove the piece. I just uploaded the model and it is under review. You will soon be able to print it with the improvements you requested. Link https://makerworld.com/es/models/2072312-trofast-ikea-tripp-trapp-optimized#profileId-2238381
(Edited)
1
Reply
@EOD_LAB
The Stokke chair for which I designed these adapters is also from 2024
Show original
1
Reply
@user_2101246335
Very nice fit
The designer has replied
designer
1
Reply
@EOD_LAB
Thanks for your review and support for my model
(Edited)
Show original
0
Reply
@Brommel
Boosted
Print Profile
0.2mm layer, 6 walls, 25% infill
Perfect fit, good and fast print Attaching it to the chair is quickly done with a few simple steps, the Trofast basket sits nicely and snugly in the guides Thank you very much for the great work! 👌😊
The profile uploader has replied
Show original
profile
1
Reply
@EOD_LAB
Thank you very much for your review I'm glad it was useful
Show original
0
Reply
@Huuuah
Great model, it fits perfectly with no looseness compared to other models I've printed before. Considering that PETG supports are inherently difficult to remove, I changed the support interface to PLA and the support type to tree supports. After printing, the supports were easier to remove (supports need to be trimmed to be removed). Thanks for sharing!
Show original
designer
1
Reply
@cojoj
Print Profile
0.2mm layer, 6 walls, 25% infill
Fit could be tighter. was too loose to my liking, and also wasn’t able to use lid with it.
The profile uploader has replied
0
Reply
@EOD_LAB
A tighter fit could compromise the part when inserting it and cause it to fracture That part was designed from scratch and several tests were done to achieve the best tolerances The lid can be used without problem, which is why it was designed with the reduced upper overhang As you can see in the photo I have attached, I personally use the lid without any problem Check if there was any error during the printing process or deformation of the material you are using No user has reported problems using the lid or with the fit of the part, you are the first Send a photo and I will try to help you Thank you for downloading and printing my design
(Edited)
Show original
0
Reply
@KingSausage
Print Profile
0.2mm layer, 6 walls, 25% infill
Need a little bit of force, but fits perfect.
0
Reply
No more

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

IKEA Skadis
IKEA Skadis
AU3D
83.1 k
18.8 k
Ikea Skadis Hooks
Ikea Skadis Hooks
Marc Elbichon
24.9 k
6.3 k
Plier Holder for IKEA Skadis
Plier Holder for IKEA Skadis
Alex
11.8 k
2.7 k
IKEA Skadis Tilt Drawer
IKEA Skadis Tilt Drawer
eethansshen
26.3 k
12.2 k