Under Sink Organizer - Free 3D Print Model

Search models, users, collections, and posts

Ysoh

Tools>Organizers

IP Report

Print Profile(2)

All

X1 Carbon

P1P

X1E

H2C

H2D

H2S

H2D Pro

P2S

P1S

X2D

A2L

A1 mini

0.2mm layer, 2 walls, 10% infill

Designer

15.2 h

7 plates

4.9(83)

Profile for a1 mini, same size

13.8 h

8 plates

5.0(3)

Open in Bambu Studio

Boost

1263

5292

138

1.8 k

1.1 k

Released

Description

I'm sharing my latest creation: an organizer for your household products, designed to fit under your sink or in a standard cupboard.

For now, only one width and one depth are available. I’ll soon offer additional sizes compatible with printers ranging from A1 to X1.

However, you can already customize the height of your double shelf using the available 100 mm and 200 mm spacers.
Just be mindful of the final rigidity depending on the height you choose.
For my own setup, I went with 300 mm (100 + 200).

Assembly is fairly simple — glue isn’t necessary (I didn’t use any). Just print the appropriate clips.

Fire up your printers! You can support me by boosting the model.

Got improvement ideas? Feel free to leave a comment.

kitchen

organizer

sink

Comment & Rating (138)

@Cyriacs

very good base! I repurposed it: adjusted dimensions and added side connections. 4 deck boxes fit one behind the other Thanks for that

(Edited)

Show original

@si3dservices

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

Fantastic design! Drawer was a little tight at first, but loosened up quickly once I'd slid it a few times (which is much better than being super loose!) I am AMAZED at how well the "X" shaped dowels work in this design for putting everything together. No glue needed. Thank you!

The profile uploader has replied

@Ysoh

Thank you for your feedback. I’m really happy that it’s working really well for you too 🙂. I like your cat :D

(Edited)

@si3dservices

Boosted

Replying to @Ysoh :

Finally got a Boost to share. It's well earned! I'm printing a second one for my own bathroom sink now. :D

@Cosmyn_3D

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

Just perfect. I only modified the dimensions to fit my needs. Thx 😊

(Edited)

The profile uploader has replied

@Ysoh

Thank you and good job :)

Show original

@ADiana

with which printer did you print it

Show original

@Cosmyn_3D

Boosted

Replying to @ADiana :

P1S

@Cyriacs

Has anyone else also had problems connecting the two drawer elements? the x prints very fragile/poorly with supports

Show original

@lemon42

yes but I ended up just hot gluing them together

@Cyriacs

I printed the drawers upright, there the supports are better and the edges are much better

Show original

@DnJProductions

Print Profile

0.2mm layer, 2 walls, 10% infill

For some reason this was smaller than I expected however does it's job and has a simple assembly. You could easily add more drawers for height. As other reviews have mentioned, at first the drawers can stick a bit however after a few back and forths slide nice and smooth. Printed in PLA.

The profile uploader has replied

@Ysoh

Oh thank you for your review. great job 👍

(Edited)

@Volti3DLand

Boosted

Print Profile

0.2mm layer, 2 walls, 10% infill

It turned out great and was exactly what I needed. It's a well thought out design. The connections took a little effort and are nice and snug. Great job, thanks!

@juanclazaro

Print Profile

0.2mm layer, 2 walls, 10% infill

Thanks a lot for the model. The idea is great, and it prints easily. However, the connectors, in my opinion, do not work properly. Not sure if I will be able to explain it correctly. What you see in the image has happened several times, the wholes are deeper that half the connector height, therefore the connector can almost be fully inserted in the piece. Not sure if it might have been my fault when building the model, but I haven’t found the cause so far apart from what I explained above.

Other Issues:The wholes are deeper that half the connector height, when that happens it cannot be used to connect the piece with another.

@monkeydrizio

Boosted

Really spectacular, I made my wife fall even more in love with 3D printing. We were trying to buy something similar but I couldn't find the right size for me. This print solved the problem!

The designer has replied

@Ysoh

oh Nice !

@ihaveeyeballs

you owe me a whole filament roll. 200mm clip went all the way in. thanks for the waste of time and money.

@theawesome1

Boosted

Nice design, thanks! Material: Bambu PLA Matte Dark Chocolate Elegoo PLA Matte Black

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.