DnD Monster Flail Snail TTRPG Dungeon Miniature

Thank you all for your support. I'm always happy to hear your opinions and suggestions for new models. So please share them in the comments.

You can offer me a coffee and support my work here >>> https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support. The website also includes a commercial license that allows you to sell all my existing models.

https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support.

Flail Snail  - Two versions 40mm and 60mm on separate plates for easier printing.

Large Elemental, Unaligned

Opis (po angielsku):
A flail snail is a magical creature that roams subterranean realms, its massive, colorful shell shimmering with prismatic light. It uses its flail-like tentacles to bludgeon foes, and its shell emits magical resistance that can even disrupt spellcasting.

Stat Block

Armor Class: 16 (natural armor)
Hit Points: 52 (5d10 + 25)
Speed: 30 ft.

Saving Throws: Con +8
Damage Resistances: Fire
Damage Immunities: Poison
Condition Immunities: Charmed, Frightened, Poisoned
Senses: Darkvision 60 ft., Tremorsense 60 ft., Passive Perception 10
Languages: —
Challenge: 3 (700 XP)
Proficiency Bonus: +2

Traits

Antimagic Shell.
The snail’s shell creates an antimagic field in a 30 ft. radius. Spells cast in this area have a 20% chance to fail.

Flail Tentacles.
The snail has 4–5 flail tentacles (DM’s choice). If it takes 10 damage or more in one turn, one tentacle may fall off.

Actions

Multiattack.
The flail snail makes one flail attack for each tentacle it has.

Flail. Melee Weapon Attack: +6 to hit, reach 10 ft., one target.
Hit: 6 (1d6 + 4) bludgeoning damage.

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations: In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

•  

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support