DnD Monster Desert Bulette TTRPG Dungeon Miniature

Thank you all for your support. I'm always happy to hear your opinions and suggestions for new models. So please share them in the comments.

You can offer me a coffee and support my work here >>> https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support. The website also includes a commercial license that allows you to sell all my existing models.

https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support.

Desert Bulette

 This fearsome land shark has adapted to the harsh desert climate. Its armored plates are sun-bleached and sand-worn, blending seamlessly with the dunes. Unlike its forest or mountain kin, the desert bulette burrows effortlessly through dry, compact sand and often ambushes prey beneath the surface. Hunters and nomads alike fear the sudden eruption of sand when this predator strikes.

Large monstrosity, unaligned

Armor Class: 17 (natural armor)
Hit Points: 94 (9d10 + 45)
Speed: 40 ft., burrow 40 ft.

STATISTICS

Saving Throws

DEX +3, CON +7

Skills                           Perception +4

Damage Resistances

Bludgeoning, Piercing, and Slashing from nonmagical attacks

Senses

Darkvision 60 ft., Tremorsense 60 ft., Passive Perception 14

Languages

—

Challenge

CR 5 (1,800 XP)

TRAITS

Standing Leap.
The bulette's long jump is up to 30 ft. and its high jump is up to 15 ft., with or without a running start.

Earth Glide.
The bulette can burrow through nonmagical, unworked earth and stone. While doing so, it doesn't disturb the material it moves through.

ACTIONS

Multiattack.
The bulette makes two attacks: one with its bite and one with its claws.

Bite. Melee Weapon Attack: +7 to hit, reach 5 ft., one target.
Hit: 30 (4d10 + 4) piercing damage.

Claws. Melee Weapon Attack: +7 to hit, reach 5 ft., one target.
Hit: 14 (2d8 + 5) slashing damage.

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations: In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

•  

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support