DnD Monster Sorrowsworn TTRPG Dungeon - Miniature

Thank you all for your support. I'm always happy to hear your opinions and suggestions for new models. So please share them in the comments.

You can offer me a coffee and support my work here >>> https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support. The website also includes a commercial license that allows you to sell all my existing models.

https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support.

Sorrowsworn – The Angry
Medium Aberration, Neutral Evil

Armor Class 16 (natural armor)
Hit Points 136 (16d8 + 64)

Speed 30 ft.   STR 18 (+4)    DEX 12 (+1)   CON 18 (+4)   INT 11 (+0)   WIS 14 (+2)   CHA 13 (+1)

Saving Throws Dex +4, Con +7, Wis +5
Skills Perception +5, Insight +5
Damage Resistances psychic; bludgeoning, piercing, and slashing from nonmagical weapons
Damage Immunities poison
Condition Immunities charmed, frightened, poisoned
Senses darkvision 60 ft., passive Perception 15
Languages Deep Speech, telepathy 120 ft.
Challenge 9 (5,000 XP)
Proficiency Bonus +4

Innate Despair Aura (1/day)

Each creature that starts its turn within 30 feet of the Sorrowsworn must succeed on a DC 15 Wisdom saving throw or be affected by bane for 1 minute. Targets can repeat the save at the end of their turns.

Emotional Siphon

Whenever a creature within 30 feet fails a saving throw against fear or despair, the Sorrowsworn regains 10 hit points.

Multiattack

The Sorrowsworn makes two slam attacks.

Slam

Melee Weapon Attack: +8 to hit, reach 5 ft., one target.
Hit: 15 (2d10 + 4) bludgeoning damage.

Enraged Form (Recharge 5–6)

As a bonus action, the Sorrowsworn channels its inner agony into raw aggression. For 1 minute, it gains advantage on all attack rolls and can make an additional slam attack as part of its Multiattack.

Legendary Actions (Optional)

The Sorrowsworn can take 2 legendary actions, choosing from the options below. Only one legendary action option can be used at a time, and only at the end of another creature’s turn. It regains spent legendary actions at the start of its turn.

• Lash of Misery. The Sorrowsworn makes a slam attack.
• Maddening Howl (Costs 2 Actions). Each creature of its choice within 15 feet must succeed on a DC 15 Wisdom save or be frightened until the end of its next turn.

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations: In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

•  

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support