Golf Putting Gates - Free 3D Print Model

Search models, users, collections, and posts

Nebuzar

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

P2S

H2D

H2S

H2D Pro

A1 mini

H2C

X2D

A2L

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

Designer

2.1 h

3 plates

4.5(13)

Gate Feet Version 2

Designer

18 min

1 plate

5.0(1)

Putting Gates with Spikes

Designer

1.4 h

3 plates

A1 Profile 0.2mm layer, 2 walls, 15% infill

2.3 h

3 plates

5.0(3)

Open in Bambu Studio

Boost

159

549

351

266

Released

Description

These are practice putting gates. 4.25 inches is the hole side down to 2.5 inches which is just barely big enough for the ball. These are great to help you practice accurate putting at home.

Feet are designed to be glued on.

Printed in PLA for indoor use. If you wish to use them outside in the summer I would suggest using a higher temp material.

STL files available so you can modify for your specific needs.

Gate Feet Version 2 added. These have tighter tolerances on the holes for a tighter fit with the gates so no glue should be needed but is still recommended.

Gates with Spikes added for outdoor use on practice greens for use before a round or for training.

Comment & Rating (21)

@AlexCo3D

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

cute little item

@user_3701339313

Print Profile

A1 Profile 0.2mm layer, 2 walls, 15% infill

@user_2518327133

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

love these gates. I’ve had requests from other golfers for them and our Pro is using them for lessons. I drilled holes in the feet to hold down with golf tees.

The profile uploader has replied

@user_2863529336

I have added a version that has spikes on the bottom for use on practice greens for training and lessons.

@3DFoxx

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

does what it needs to do but the posts into the feet could be tighter to stay in more snug. I also feel like the gates could be stepped down in side where they could fit inside each other if laying them down flat.

The profile uploader has replied

@user_2863529336

This was originally designed 10 years ago when printers were not as accurate. Version 2 will be uploaded soon that has tighter tolerances for the more accurate printers available today.

(Edited)

@po045cop

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

the biggest one refused to successfully print the nubs that go into the feet. tried 3x

The profile uploader has replied

@user_2863529336

Thank you for bringing this to my attention. I have found and fixed the issue and will update the print profile so no one else has this issue.

@Teri_B_Hansen

Print Profile

Gate Feet Version 2

I like that these feet are as wide as the arches. The print turned out great and assembled well.

@Teri_B_Hansen

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

These turned out nice! I used the thinner foot stands. I made them for my son and he is excited to practice putting indoors. (His wife is even on board, ha ha)

@Eiscool

Print Profile

A1 Profile 0.2mm layer, 2 walls, 15% infill

So perfect for our robotics students to use with their Sphero Mini’s!

(Edited)

@DanBot007

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

perfect solution for a beginner golfer since my putting sucks I hope these help

@futibola

Print Profile

0.4mm nozzle, 0.20mm layer, 2 walls, 15% infill

They are very good in size but weigh so little that they fall over at the slightest touch. And on natural grass, given the low weight, it is difficult to keep them standing if there is a slight slope

Show original