Hand Vise v1 - Free 3D Print Model

Search models, users, collections, and posts

SciFientist

Tools>Hand Tools

IP Report

Print Profile(2)

All

X1 Carbon

P1S

A1 mini

H2D

X1E

P1P

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 100% infill

Designer

3.3 h

1 plate

4.7(33)

color_sequence_all at once_0.2mm layer, 4 walls, 100% infill

3.6 h

1 plate

5.0(2)

Open in Bambu Studio

Boost

752

1969

601

301

Released

Description

I needed a vise that can hang on to small 3d printed parts to do finishing work without damaging them. This is what I came up with.

In my video I cut a slot in the bolt to insert a retaining clip. If you don't want to do this, you can install a spring on the bolt in between the two jaws.

I printed this with 100% infill

Parts List:

M5 50mm bolt

M5 nut

Retaining Clip or Spring

vise

hand vise

clamp

Comment & Rating (44)

@SM_Design

Boosted

Print Profile

0.2mm layer, 2 walls, 100% infill

Instead of a spring, I used a nut and a bit of Loctite glue. Very good and nicely designed model. The attachments are top-notch — exactly what I needed. You’ve got a boost from me!

@HealingBear

Print Profile

0.2mm layer, 2 walls, 100% infill

finally got it done lol had to go get a screw. I thought I had one. It was not long enough, then I tried cutting the groove to put the little key in did not have The proper tool so I tried to use my bandsaw, cut it a little too deep so I came up with a different solution but I love the print. I love how solid it is. Thank you for your time and effort in creating this print.

The profile uploader has replied

@SciFientist

Awesome color choices! Has Reptar vibes. can you explain the lock on the threads? how does it work?

(Edited)

@HealingBear

Replying to @SciFientist :

when I attempted to cut a groove around the bolt/screw, I cut it a little too deep for the key clip that I had and it was too loose so I took some wire and a pair of needle nose and twisted it very tightly in two different directions two different pieces of wire the first wire I put into the groove that I had cut and tightened very tightly. The second wire I put right behind that one and sniped them off short so that they would clear the distance. Of course I put a washer on before I did that so it keeps the washer from being able to slide by.

@LeatherSmith

Boosted

Print Profile

0.2mm layer, 2 walls, 100% infill

Awesome tool and design! Thanks a lot for making this. I had to re orient the parts in the slicer. not sure if you intended to orient them vertically or not. but it really should be printed laying flat. also 100% infill is not the best option for strength. more walls and about 42% infill is where you want to be for strength. maybe design a little detent for the jaw replacements to snap and hold in place when you change them out. Thanks again!

@user_2413450664

Print Profile

0.2mm layer, 2 walls, 100% infill

Everything worked perfectly Thank you

Show original

@darthheathy

n boh pulo ngon na leubèh-leubèh .y.

@ted.andersson85

This tool was like a gift from God to get this week's project done 😍🇸🇪

@sonb610730

it come out pretty good i suggest make hollow part of handle as sotrage to store jaw inserts, also will be good if handle itself can be separate as module, and design a base for it, so it have normal vise funtion and hand vise function also also! jaw inserts come loose from time to time...

@tepsley

Print Profile

0.2mm layer, 2 walls, 100% infill

Works like a charm, thank you!

@jakew1lldoit

Boosted

Print Profile

0.2mm layer, 2 walls, 100% infill

I printed mine same colors but with ASA. I had to tweak a few of things and got it about 80% of the way there . Still not as nice surface finish everywhere as the PLA version. But still . Really good model. Great job!