Marvins_Creed

cover

1000050173.jpg

1000050171.jpg

1000050274.jpg

1000050276.jpg

1000051720.jpg

plate_1.png

plate_2.png

plate_3.png

plate_4.png

plate_5.png

2025-05-11_713ada5d1b56b8.jpg

Supports only recommended/needed for Pipe CornerPipes can also be printed laid down for better stability but with the need of supports inside

0.2mm layer, 2 walls, 15% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

--------- Deutsche Anleitung weiter unten ----------An adaptable drainage system that allows to redirect the water flow from a raised bed in any direction instead of simple downwards dripping holes. The Connector should be adapted to the bottom board thickness of the raised bed, so the Pipe corner and the connecter fit tightly together and press the liner against the board to ensure a seal. The connecter was designed for a bottom board thickness of 14 mm and a hole with a diameter of 19 mm. Feel free to scale the connector up and down to fit your needs but dont forget to scale all parts evenly. I also added a conector with a elongated pipe that can be shortened using f.e. TinkerCAD until fit. The pipe of the connector should be about 7 mm + board thickness minus 1 mm. Make sure to test the fitting of the connector and pipe corner to your raised bed before printing the ramaining parts.&nbsp;The whole system can then be printed in a simple configuration of:1 Pipe Corner + 1 drainage connector + 1 drainage pipe&nbsp;The system can also be elongated ad infinitum with the following configuration:1 Pipe Corner + 1 drainage connector + 1 drainage pipe elongation starting piece + 1 drainage pipe elongation end piece(optionally + as many drainage pipe elongation middle pieces as you want to put in between)&nbsp;For very long configurations glueing the pipes together is recommended.&nbsp;-----------------------------------------------------------------------&nbsp;Ein anpassungsfähiges Abflusssystem, das es ermöglicht, den Wasserfluss aus einem Hochbeet in jede beliebige Richtung umzuleiten, anstelle von einfachen, nach unten gerichteten Tropflöchern. Das Verbindungsstück sollte an die Bodenplattendicke des Hochbeets angepasst werden, so dass die Rohr Kurve und der Adapter eng zusammenpassen und die Folie gegen die Platte drücken um eine Abdichtung sicherzustellen. Das Verbindungsstück wurde für eine Bodenplattendicke von 14 mm und ein Loch mit einem Durchmesser von 19 mm entworfen. Sie können den Adapter nach Belieben vergrößern oder verkleinern, aber vergessen Sie nicht, alle Teile gleichmäßig zu skalieren. Ich habe auch einen Adapter mit einem verlängerten Rohr hinzugefügt, der z.B. mit TinkerCAD gekürzt werden kann, bis er passt. Das Rohr des Adapters sollte etwa 7 mm + Plattendicke minus 1 mm lang sein. Stellen Sie sicher, dass Sie das Passen des Adapters und der Rohr Kurve an Ihrem Hochbeet testen, bevor Sie die übrigen Teile drucken.&nbsp;Das ganze System kann dann in einer einfachen Konfiguration gedruckt werden:1 Rohr Kurve+ 1 Abfluss Adapter + 1 Abfluss Rohr&nbsp;Das System kann auch mit der folgenden Konfiguration endlos verlängert werden:1 Rohr Kurve+ 1 Abfluss Adapter + 1 Rohr Verlängerung Startstück+ 1 Rohr Verlängerung Endstück(optional + so viele Abfluss Rohr Verlängerung Mittelstücke, wie Sie dazwischen setzen wollen)&nbsp;Bei sehr langen Konfigurationen wird empfohlen, die Rohre miteinander zu verkleben.

--------- English instructions below ---------An adaptable drainage system that redirects raised bed water flow in any direction, instead of simple downward dripping holes. Adapt the connector to your raised bed's bottom board thickness, ensuring the pipe corner and connector fit tightly, pressing the liner against the board for a seal. The connector is designed for a 14 mm thick bottom board and a 19 mm diameter hole. Scale the connector as needed, but maintain even scaling across all parts. A connector with an elongated pipe is included; shorten it as needed (e.g., using TinkerCAD). The connector pipe should measure approximately 7 mm + board thickness - 1 mm. Test the connector and pipe corner fit before printing other parts.&nbsp;The complete system can be printed using this simple configuration:1 Pipe Corner+ 1 drainage connector+ 1 drainage pipe&nbsp;The system can be infinitely extended using this configuration:1 Pipe Corner+ 1 drainage connector+ 1 drainage pipe elongation starting piece+ 1 drainage pipe elongation end piece(optionally + as many drainage pipe elongation middle pieces as needed)&nbsp;For extensive configurations, gluing the pipes is recommended.&nbsp;-----------------------------------------------------------------------&nbsp;A versatile drainage system diverting water flow from a raised bed in any direction, rather than simple downward drainage holes. Adjust the connector to match your raised bed's baseboard thickness, ensuring a tight fit between the pipe elbow and connector, pressing the liner firmly against the board to create a seal. The connector is designed for a 14 mm thick baseboard and a 19 mm diameter hole. Feel free to resize the connector, but remember to scale all components proportionally. A connector with an extended pipe is included; this can be trimmed to the appropriate length using a program such as TinkerCAD. The connector pipe should be approximately 7 mm + board thickness - 1 mm. Before printing the remaining components, verify the connector and pipe elbow fit your raised bed.&nbsp;The entire system can be printed in this simple configuration:1 Pipe Elbow+ 1 drainage connector+ 1 drainage pipe&nbsp;The system can also be extended indefinitely using the following configuration:1 Pipe Elbow+ 1 drainage connector+ 1 drainage pipe extension starting piece+ 1 drainage pipe extension end piece(optionally + as many drainage pipe extension middle pieces as required)&nbsp;For very long configurations, gluing the pipes together is recommended.

Raised bed drainage

ASIA

Print Profile(1)

Description

Comment & Rating (0)

License

Related Models