Search models, users, collections, and posts

38 Special 5 Shot Speed Loader Tray J-Frame

ogre56
Hobby & DIY>Sport & Outdoors
IP Report

Print Profile(1)

All
A1
H2D Pro
H2S
H2C
H2D
P2S
X2D
A2L
0.28mm layer, 2 walls, 15% infill
0.28mm layer, 2 walls, 15% infill
Designer
5.4 h
2 plates
5.0(4)
Open in Bambu Studio
Boost
46
147
31
1
110
48
Released 

Description

This tray is ro assist in refilling speed loaders during competition. The tray fits into the bottom box that is used for storing empty brass.

 

Being just a functional part I printed these using the .28 Extra Draft profile.

 

 

38special
speedloader
revolver
smithandwesson

Comment & Rating (31)

(0/1000)
@MStarmer
Boosted
Since these are absolutely freaking awesome I have another request. With everyone jumping on the (6) shot .32 H&R Mag J-Frames (432/632 Ultimate Carry) I would love to see this and the (2) load configuration like you did for the .38 special! Hopefully I generated some traffic to your page, I linked it in one of my revolver groups!
The designer has replied
3
Reply
@user_1912465630
I'd never even heard of that one. I'll have to see if I can find someone who has one or even a speed laoder. Thanks for the suggestions, I enjoy building new things. Going to be uploading an extended base pad for a ruger SR22. Please keep the ideas coming and I will see what I can do.
1
Reply
@MStarmer
Boosted
Replying to @user_1912465630 :
HKS 32-J would be the speedloader. I'd gladly pay for a speedloader for ya!
0
Reply
@user_1912465630
Replying to @MStarmer :
Have gotten 6 rounds of 32HR and have ordered a speed loader. Should be about a week and I will have it posted. Thanks again!!
0
Reply
@MStarmer
Boosted
One more suggestion for another one. I would love to see this in a 2 load configuration for desk drawer / nightstand duty.
The designer has replied
0
Reply
@user_1912465630
I have it designed (was that simple to change) but have to wait until morning to print and upload it. Printer is working on another HueForge ;)
1
Reply
@user_1912465630
Thanks for the suggestion, here it is https://makerworld.com/en/models/1387417-38-special-2x-speed-loader-tray-s-w-j-frame#profileId-1437089
0
Reply
@MStarmer
Boosted
Printed great! Should work for the Ruger SP-101 and Ruger LCR in .38/.357 as well.
The designer has replied
0
Reply
@user_1912465630
Awesome!! Thanks for the review and picture!!
1
Reply
@Matt_XT600
Why did they make the box longer than the charging board? Wouldn't it make sense anymore, you would make it so wide that it fits exactly and the box only so high that the shots don't fall out during transport? Regards
The designer has replied
0
Reply
@user_1912465630
I was asked to make it this way so that during competition you take the tray to the line, seperate the two pieces. The bottom section then holds the empty brass. I'm honestly not sure how you are suggesting I do it. I'm always looking for another design to work on..... Thanks for the interest!
1
Reply
@Matt_XT600
Replying to @user_1912465630 :
Yes, it's certainly good that the box can be separated from the tray for the empty brass cartridges. But it bothered me that the two trays weren't compatible in terms of size. I've now designed my own tray. It's now solved in such a way that the width has been adjusted and the height reduced. This allows the cartridges to be stored inside without them falling out. This way, you can prepare them at home. Before the competition, you can then separate the two trays and set them up separately.
1
Reply
@user_1912465630
Replying to @Matt_XT600 :
Very nice!!
1
Reply
@Sarah.315
hello - can you also make something like this for the P1S
The designer has replied
Show original
0
Reply
@user_1912465630
Absolutely, it will print just fine on the P1S
0
Reply
@Sarah.315
Is it possible that Germany is blocked then? It says P1S is not supported for me
Show original
0
Reply
@Sarah.315
P2S is with me and others
Show original
0
Reply
@user_2537216702
Print Profile
0.28mm layer, 2 walls, 15% infill
Worked great print profile is also great
(Edited)
The profile uploader has replied
Show original
0
Reply
@user_1912465630
Awesome, thanks!!!!
0
Reply
@MStarmer
Boosted
Thank you!
The designer has replied
0
Reply
@user_1912465630
Sure, thanks for the BOOST!!
0
Reply
@Alex0780
Print Profile
0.28mm layer, 2 walls, 15% infill
The profile uploader has replied
0
Reply
@user_1912465630
Thanks!!
0
Reply
@user_4251396362
Print Profile
0.28mm layer, 2 walls, 15% infill
The profile uploader has replied
0
Reply
@user_1912465630
Thanks!!!
0
Reply
@Matt_XT600
Print Profile
0.28mm layer, 2 walls, 15% infill
The profile uploader has replied
0
Reply
@user_1912465630
Thanks!!
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Planter Pot with Drip Tray, 12 cm / 5 inches
Planter Pot with Drip Tray, 12 cm / 5 inches
tempo
16.1 k
4.7 k
Framed HSW - 5 Sets - Honeycomb Storage Wall
Framed HSW - 5 Sets - Honeycomb Storage Wall
KYZ Design
19.2 k
4.7 k
6-Shot Disc Shooter
GIF
6-Shot Disc Shooter
uhltimate
27.1 k
6.2 k
38 Special 2x Speed Loader Tray J-Frame
38 Special 2x Speed Loader Tray J-Frame
ogre56
95
29