Its On My Mind

cover

QTR.gif

plate_1.png

plate_2.png

2025-04-25_75fde2e38cb198.jpg

0.2mm layer, 2 walls, 15% infill

Peeler

shared image.jpg

Artificial q-tips if you don&#39;t have any ;)

3d Printed Q-tips 0.2mm layer, 4 walls, 15% infill

The_C

图片4.jpg

图片1.png

图片2.png

图片3.png

两盘打印的双色模型，无需 AMS，A1 mini 可用。 修复多处可能造成缺陷的悬垂和桥接。 重新绘制支撑，减少不必要的支撑，更容易拆除。 对于底面有 45°以下的悬垂，Brim 与模型的间隙应大于 0.2mm 便于拆除。 工艺参数可用于 PLA 和 PETG。默认使用 PETG HF，请自行修改为你校准过的耗材参数。 无论什么模型，始终建议打印前清洁打印板并适当涂胶，避免模型翘边、脱离导致“炒面”。 &nbsp;修复问题如下：<ol><li>增加 revolver_4.52.STL 墙层数，增加桥接面积并优化悬垂。</li><li>用修改器将墙层数设为 1，并调整线宽，以增加桥接面积。</li><li>用负零件删除完全悬空部分，避免产生外墙缺陷。</li></ol>

Two-plate printed dual-color model, no AMS required, A1 mini compatible. Multiple overhangs and bridges prone to defects have been repaired. Supports have been redesigned to minimize unnecessary supports and ease removal. For overhangs with a base angle of less than 45°, the gap between the brim and the model should be greater than 0.2mm for easier removal. Process parameters are suitable for PLA and PETG. PETG HF is used by default; please modify this to your calibrated filament parameters. Regardless of the model, it is always recommended to clean the build plate and apply an appropriate adhesive before printing to prevent warping and detachment resulting in spaghetti. &nbsp;The following issues have been addressed:<ol><li>Increased wall layers for revolver_4.52.STL, increased bridge area, and optimized overhangs.</li><li>Used a modifier to set the wall layer count to 1 and adjusted the line width to increase the bridge area.</li><li>Used negative parts to remove completely unsupported sections, avoiding exterior wall defects.</li></ol>

Two plates, dual color, no AMS required, A1 mini compatible.

zackza

photo_2025-05-05_10-31-41.jpg

1 plate! and added brim to the tall stick lookin ahh part, thatll teach em! thatll learn em good not to de-adhere to MY bed

1 plate, 1 color, 0.2mm layer, 2 walls, 15% infill

单盘逐件打印的双色模型，需要 AMS。修复多处可能造成缺陷的悬垂和桥接。重新绘制支撑，减少不必要的支撑，更容易拆除。对于底面有 45° 以下的悬垂，Brim 与模型的间隙应大于 0.2mm 便于拆除。工艺参数可用于 PLA 和 PETG。默认使用 PETG HF，请自行修改为你校准过的耗材参数。无论什么模型，始终建议打印前清洁打印板并适当涂胶，避免模型翘边、脱离导致“炒面”。  &nbsp;修复问题如下：<ol><li>增加 revolver_4.52.STL 墙层数，增加桥接面积并优化悬垂。</li><li>用修改器将墙层数设为 1，并调整线宽，以增加桥接面积。</li><li>用负零件删除完全悬空部分，避免产生外墙缺陷。  </li></ol>

Single plate, piece-by-piece printing of dual-color models, requires AMS.Fixes multiple overhangs and bridges that may cause defects.Redrawn supports, reduces unnecessary supports, easier to remove.For overhangs below 45° on the bottom surface, the gap between the brim and the model should be greater than 0.2mm for easier removal.Process parameters can be used for PLA and PETG. PETG HF is used by default, please modify it to your calibrated filament parameters.Regardless of the model, it is always recommended to clean the printing plate and apply appropriate glue before printing to avoid model warping and detachment leading to spaghetti. &nbsp;The following issues have been addressed:<ol><li>Increased the number of wall layers for revolver_4.52.STL, increased the bridge area, and optimized overhangs.</li><li>Used a modifier to set the number of wall layers to 1 and adjusted the line width to increase the bridge area.</li><li>Used a negative part to delete the completely overhanging parts to avoid wall defects. &nbsp;</li></ol>

Single plate dual color, fixes overhangs and bridges that may cause defects, optimized supports.

Tomecio

obraz_2025-04-28_224634199.png

BRIM ON, 0.2mm layer, 2 walls, 15% infill

FratelliUmaniCreations

WhatsApp Image 2025-12-14 at 21.07.49_(1).jpeg

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

This is a fully 3D-printed Q-tip revolver that can shoot six Q-tips in succession using a internal indexing mechanism. <ol><li>How It Works – <figure class="media"><oembed url="https://www.youtube.com/shorts/tzUK9QvNcXE"></oembed></figure></li><li>Assembly Guide – https://www.youtube.com/shorts/0xAlr_B343g</li></ol>Make sure your printer is well-calibrated for small tolerances. PLA is recommended for best results.

Print Profile(7)

Description

Comment & Rating (637)

License

Related Models

Q-tip Revolver

Print Profile(7)

Description

Comment & Rating (637)

License

Related Models