Search models, users, collections, and posts

Mr. Toad's headstone statue

jjrice23
Household>Decor
IP Report

Print Profile(4)

All
A1
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L
P1S
X1 Carbon
X1
P1P
X1E
A1 mini
0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
Designer
11.5 h
1 plate
4.9(10)
0.2mm layer, 4 walls, 12% infill
0.2mm layer, 4 walls, 12% infill
Designer
11 h
1 plate
0.2mm layer, 3walls, 12% infill
0.2mm layer, 3walls, 12% infill
Designer
10.8 h
2 plates
0.2mm layer, 3 walls, 12% infill
0.2mm layer, 3 walls, 12% infill
Designer
9.4 h
2 plates
Open in Bambu Studio
Boost
155
412
35
17
237
106
Released 

Description

Couldn't find a model of Mr. Toads gravestone statue from Walt Disney Worlds Magic Kingdom, so here it is. Actual gravestone is located in the pet cemetery outside of the rides exit!

mr toad
disney
disneyland
mr toads wild ride

Comment & Rating (35)

(0/1000)
@TreGrizz
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
First try the print failed due to a stuck ams. I Was able to split and print toad by himself then glued onto the base.Everything fit together great afterward and the print turned out really well. .
The profile uploader has replied
profile
1
Reply
@jjrice23
came out really awesome!!! thank you for the post. I’ll go on and split them and upload that profile as well.
0
Reply
@user_842990447
Print Profile
0.2mm layer, 3 walls, 15% infill
As Disney lovers we love this print! He’ll be a permanent part of our Halloween cemetery.
The profile uploader has replied
profile
1
Reply
@jjrice23
looks great!!! thank you so much for the rating and picture.
(Edited)
1
Reply
@TreGrizz
Boosted
Great print! I split the base and Mr Toad and printed separately to make painting easier. Slowing down the print a bit would help with a few overhang, but not necessary especially of you are doing any post processing. TY for the great upload!
1
Reply
@user_3676504799
Print Profile
0.2mm layer, 3 walls, 15% infill
profile
1
Reply
@StretchAK
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
This looks so good! I used PLA basic marble and bronze. lots of supports because it is so tall but detaching was pretty clean.
The profile uploader has replied
profile
1
Reply
@jjrice23
Awesome, I’m so glad that you were able to get a great result!!! Thank you for your review.
0
Reply
@StretchAK
Boosted
Replying to @jjrice23 :
Any plans for other Disneyland or Disneyworld prints? This one was so elaborate, I can't imagine how long it took you to get it this dialed in.
0
Reply
@jjrice23
Replying to @StretchAK :
it really depends on the demand. I had a friend who wanted this for a family member who was a fan so if there’s demand for others I’d love to dive into it.
0
Reply
@user_2085420162
I would love to print this is there a way to print from a ps1 printer?
The designer has replied
1
Reply
@jjrice23
yea I’ll update the profile now
0
Reply
@jjrice23
should be good to go, uploaded a p1s profile as well as a version where he is split from the block and can be glued on.
0
Reply
@user_2085420162
thank you I’ll be printing tomorrow morning
0
Reply
@parasyte40
it looks like you had your brim distance set to .125 which doesn’t cause any of the brim to stick to itself, creating just a circle of unsupportive brim. one of my supports tipped over about 4 hours in. I’m going to try again but so you know you might want to update that! love the print though! hopefully it works this time.
The designer has replied
0
Reply
@jjrice23
ah man, ok, I’m going to have to check this out and update if Im able to.
1
Reply
@parasyte40
Replying to @jjrice23 :
I investigated to make sure it wasn’t any of my settings but because it was a 3mf file it just loaded whatever settings you had. Do you find rectilinear works better for the infill on this print than gyroid? There was a circular/oval infill on the square marble base so I was curious if that was because I switched it to gyroid.
0
Reply
@jjrice23
Replying to @parasyte40 :
honestly I had mistakenly uploaded it with setting I had on another model. I updated the settings and infill and it should be ready after makerworld verifies
0
Reply
@Brogdan
Hey, awesome looking print. How did you get that nice copper effect? Copper PLA and drybrushed black paint?
The designer has replied
1
Reply
@jjrice23
Hey. yea so for this I printed it in a galaxy black filament the I used “antique gold” rub n buff after to get the brass/copper effect
1
Reply
@Brogdan
Replying to @jjrice23 :
aah the other way around, yea makes sense. Thanks dude!!
0
Reply
@user_670030341
Print Profile
0.2mm layer, 3 walls, 15% infill
Absolutely AMAZING! THANKS!
The profile uploader has replied
profile
1
Reply
@jjrice23
hey thanks, i appreciate it!
0
Reply
@don5219
Print Profile
0.2mm layer, 3 walls, 15% infill
Came out great. I'm putting him in the garden. Next time I might increase the size.
The profile uploader has replied
profile
1
Reply
@jjrice23
thank you for printing it and I’m glad it came out great!! Would love to see if you do happen to increase the size
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Mr. Snek
Mr. Snek
Printzee
10.2 k
4.3 k
Yoshi from Super Mario
Yoshi from Super Mario
It's a me
15.3 k
5.5 k
Fly Trap Toady
Fly Trap Toady
Viltsu
7.1 k
2.5 k
Tic Tac Toad
Tic Tac Toad
Mochi Makes
5.1 k
6.4 k