Search models, users, collections, and posts

Left Center Right game

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L

0.08mm layer, 2 walls, 15% infill
0.08mm layer, 2 walls, 15% infill
Designer
25.7 h
4 plates
4.5(22)

Open in Bambu Studio
Boost
59
157
32
20
268
177
Released 

Description

Print in place box with dice and chips to play Left Center Right (LCR)

Each player gets 3 chips

Enough room in the box for 48 chips, but only 24 on first plate (all that is needed for 8 players)

The following applies to each dice you roll, and you don't roll more dice than you have chips

-Roll and L and pass a chip to the left

-Roll and R and pass a chip to the right

-Roll a dot and keep your chip

-Roll a star and put a chip in the center

*We have house rules that if you roll 3 stars you get all the chips in the center

 

A complete plate is included but if you rather change the settings for each type, they are on their own plates

.08, with ironing for the chips (and dice if you want), 15%, and supports just for the latching mechanism.

65 for the bed

Comment & Rating (32)

(0/1000)

Print Profile
0.08mm layer, 2 walls, 15% infill
Love this case so much! it printed Very well on its own (had issues on the plate with everything on it) I am so excited to add this to my games collection!
profile
2
Reply
Boosted
Print Profile
0.08mm layer, 2 walls, 15% infill
ty so much heard of this game first time on Monday.
profile
1
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
Other Issues:unfortunately was looking ok, until layer 120ish then print jumped 5mm and lost it will have a look at file and try redo die, but another 5hrs... ugh tokens came out nice another file printed perfectly for die, so not sure what happened here
The profile uploader has replied
0
Reply
I get your frustration, it's not the easiest to print, but 1 star because you had issues with your printer...? Good luck
0
Reply
the idea of ratings is to honestly review the point of files is they accurately print if the print fails, quite epically (first failure in 50+prints), what else would you expect me to say, other than 1 star? happy to take advice if you have constructive advice... but I successfully printed another file immediately afterwards, not 1 issue across 9 die... however that designer did say he used your base file, so adjusted to 2 stars
0
Reply
Hi there- First I want to say that I'm new to 3D printing, only a month into it, printing here and there things that interest me. This is the first file that I needed to learn to add supports. I printed your file and it came out great except the 2 hinges broke when trying to free them. Is there something I should have changed in my settings to avoid this? I'm using the Bambu A1 and printed with Cookiecad PLA. THANKS
The designer has replied
0
Reply
Sorry, forgot the picture.
0
Reply
Replying to @gotmud49 :
Well that stinks. Sorry to hear. I have a hinge test on my uno box that you could use to get your settings fixed. The hinges should have the same tolerances. Hope this helps. https://makerworld.com/en/models/119835#profileId-148361
(Edited)
1
Reply
Replying to @makecents.3dp :
I'll check it out. Thanks for your time.
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
Excellent print, superb result
Show original
profile
1
Reply
Awesome build!
1
Reply
Boosted
Print Profile
0.08mm layer, 2 walls, 15% infill
Printed great
profile
1
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
the hinges on the case busted right away.
0
Reply
Boosted
Print Profile
0.08mm layer, 2 walls, 15% infill
I couldn't print the game pieces Repeatedly flawed tokens
Show original
0
Reply
I printed the box today. we love this game. I broke one hinge but it's cool. I can still use the box. used your profile. I was going to put my set in the case. but my dice are a tad bit to big. going to print the chips and dice you have. may print the box a bit bigger to fit my set. thanks for a great file.
0
Reply