H2D Poop pipe - Removable! - By KoBuCRAFTS!

You can place the poop bin underneath the shelve where your printer is standing. So you can choose whatever size of bin u use!

• Part 1: Poop outlet for mounting on the original screws at your Bambulab H2D printer (For X1/P1 series CLICK HERE!)
• Part 2: Poop pipe, what is attached to the outlet with 4 magnets each (6x3mm) for easy removing (Link below in model page).
   

This setup makes it easy to remove your printer for maintenance etc. Just take of the pipe and move your printer.

After maintenance place back your printer and place the magnet pipe on the outlet. Just as simple as that!
 

I have designed the model with a smooth curve, so no chance for blockages in the pipe!

The model includes 4 plates, for 4 types of poop pipes,

• 150mm straight pipe
• 250mm straight pipe
• 320mm straight pipe
• 310mm pipe with curve
   

I printed several poop containers, and a kind of pipe, but the containers were too small, or I got a blockage in the pipe.

That's why I decided to design a completely new type, and i love it!


Installation steps:

1: Download the print profile and print the plate of your choice

2: Remove the brims and eventually some leftover sharp edges

3: Place the magnets, look at orientation! (North/South pole of the magnet)
(When u place the magnets in part 1 with the north side in the housing, then u place the magnets in part 2 with the south side in the housing)

4: Remove the upper screw from the poop chute at the back of your printer.

(Photo's of my X1/P1 series Version, This H2D version is exactly the same installation!)

5: Loosen the lower screw from the poop chute at the back of your printer, just enough yout poop outlet can fit tightly over it:

6: Place the poop outlet over that screw:

7: Place the upper screw back in, (don't over tighten because the housing is just plastic and the screws are short!)

*U can place a little bit longer screws if u have the right type.

8: Move your printer and make a hole trough your shelve/table.

The distance between the back side of your printer, to the heart of the pipe is 72,5mm. 

9: Place your printer back in place, and place the pipe trough the shelve/table on the outlet.

10: Place a bin/box/container/bag or whatever u want underneath the pipe and print!
 

Your Bambu lab wil poop like it never poops before!

Link for magnets: (Amazon)

https://www.amazon.nl/LISOPO-Neodymium-magneten-mini-magneten-magneetbord/dp/B0C84SYYRC/ref=sr_1_15?__mk_nl_NL=%C3%85M%C3%85%C5%BD%C3%95%C3%91&crid=3RO0ABJBJ33KX&dib=eyJ2IjoiMSJ9.VirDiGpSfW-TVY-CMq6W_oHNbG09y2Z38LAhx9XOH-J---O7X5q-i-887_ejbEU4951gz9V1G6Yyn_OQu5fUw-9o4mUOUQG8MhdfYTnh1W_t2JECYivbu4LSU2DX13wXh37qLFCtSFqvP1qUoSmaRzLYaemi0_aEBNupX39034jsIqK_S7gCbvc4fRd1hLs1z3XyDttrLIk_XKDlRnoDuvShzObzKNMtnCBnFJvRz1EfUrWnDUSIDTMd68SfYCAG7ikCvfN35jiiY6Z_ywqXziyNiYPjlJKo1W7zw6ikS2s.o4y9jtikVT22WJJ1vx34D9epsjALPN3jakjwYBY-R2o&dib_tag=se&keywords=6x3mm+magnets&qid=1744879229&sprefix=6x3mm+magnets%2Caps%2C69&sr=8-15

Hope u like my files! U can find 50+ more models at my model page!

Created by KoBuCRAFTS!