Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E ) by Benjamin Kott

Benjamin Kott

3D Printer>3D Printer Accessories

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

Lid Handle - Bottom on Buildplate

Designer

22 min

1 plate

4.7(17)

Lit Handle - Top on Buildplate

Designer

21 min

1 plate

4.4(8)

0.2mm layer, added Brim

23 min

1 plate

5.0(2)

0.08mm layer, 2 walls, 15% infill

54 min

1 plate

5.0(2)

Open in Bambu Studio

Boost

121

196

176

Released

Description

Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )

This is a replacement for the original Handle on the Glass Hood for the P1 and X1 Series. It integrates a stand that you can flip over, to allow additional airflow without removing the Glass Hood. The hinge is printed in place and the surface area is left blank intentionally, it´s easy for you to add a logo on top, and I don't get legal issues 😜.

Installation

Just unscrew the original handle, and reuse the screws to install the replacement. Done.

I hope you enjoy the design, please leave a comment/rating if you enjoy it or share your feedback!

Comment & Rating (38)

@Mr.Haix

Print Profile

Lid Handle - Bottom on Buildplate

Nice looking Tool. Prints well, but i had to use a Brim. Thanks for Sharing 👍🏻

The designer has replied

@benjaminkott

Clean plate worked for me 😅

@Mr.Haix

Replying to @benjaminkott :

I tried to clean the bed twice, unfortunately without success :D. The bottom wall is unfortunately very narrow, maybe you could make it a bit wider. Otherwise very nice model

@benjaminkott

Replying to @Mr.Haix :

i thought about it during designing but it made the model to clunky for my taste. If the brim helps some it's a tradeoff I would take in this case.

(Edited)

@hive_co

Boosted

Print Profile

Lit Handle - Top on Buildplate

This is definitely the better profile to print with. I tried the default profile, and it resulted in a pretty ugly print.

@user_2969444751

First attempt at adding a logo onto an model, came out alright i'd say. Thanks for sharing!

@MamaChaos

5 STAR! Love this little easy gadget and added the logo for being extra. Thank you so much!

@simon.love

Print Profile

Lid Handle - Bottom on Buildplate

worked as expected.

(Edited)

@NeoBlack

Print Profile

Lid Handle - Bottom on Buildplate

The best looking Top Glass Riser integrated into Lid Handle for Bambu Lab Printers ( P1S / X1C / X1E )

@nobelfactum

Print Profile

Lid Handle - Bottom on Buildplate

@hive_co

Boosted

Print Profile

Lid Handle - Bottom on Buildplate

Other Issues:I had some over extrusion issues with this print profile. The other one that prints with the hinge open produced a much better result. This one was still functional, but would require some post-processing. I used bambu pla-matte, though, so that might be part of the problem.

@tedted

Print Profile

Lid Handle - Bottom on Buildplate

Really sleek print to both close or lift the top panel when printing Pla to vent the heat. Recommended if your Ams is not on top of the printer

@Gamp

My ABS one works (for now) even with AMS on the glass. Eats into a rubber seal a little to much for my liking though. EDIT: DO NOT USE WITH AMS ON THE GLASS. Leg holds fine but that much weight on one point on printer frame is probably not safe. Part of my plastic frame is now bent. Can't speak of use with a risers though or led frames. As I didn't use one.

(Edited)