Oral-B Electric Toothbrush Travel Case (Travel Box) - Free 3D Print Model

Search models, users, collections, and posts

Zandor

Household>Other House Models

IP Report

Print Profile(1)

All

P1S

X1 Carbon

P1P

H2C

P2S

H2S

X1E

H2D

H2D Pro

X2D

A2L

3.7 h

1 plate

4.4(10)

Open in Bambu Studio

Boost

165

588

778

380

Released

Description

Content has been automatically translated.

Show original

— New version ---

Improved flexibility of the locking tab
Added a slider for easier opening
Added a small grip for easier unlocking

Travel case for Oral B electric toothbrush.
Tested with Oral B PRO SERIES toothbrushes (but should fit other models).
Holds two brush heads.
The case is a sliding type, with a locking latch underneath.
Vents are present to prevent mold growth and water drainage if washed.

Length: 20.7 cm
Width: 6.3 cm
Height: 3.4 cm

Print tested on Creality Ender-3 V3 KE

Comment & Rating (41)

@Zetof

Hello, Nice box, print finished, but I regret that the lid tab broke on first use. I'm disappointed, as three hours of printing were for nothing! Printer: A1 Combo Filaments: Yellow PLA Basic Bambu Lab Grey Sunlu High Speed

The designer has replied

@zandor973

Hello @Zetof , My apologies for this issue I have printed three of these travel boxes and haven’t experienced this problem I strived for an optimal balance between box rigidity and tab flexibility, but it is indeed a potential weak point To be safe, gently pull the tab—just enough to unlock it, approximately 5mm

Show original

@Zetof

Replying to @zandor973 :

Hello Zandor, Thank you for your reply. I'll start a new print and be careful when opening the box. Thank you again for your work. Kind regards,

@zandor973

Replying to @Zetof :

Hello @Zetof, following your comments, I have made modifications to the case: - Improved flexibility of the locking tab - Added a slider to the back of the case for easier toothbrush removal (also reduces the amount of filament used) - Added a small grip to the end of the locking tab for improved handling If you wish to try another print, please download the new STL file (OralB_TravelBox_EXT_v2.stl) Sincerely

Show original

@yelloxygene

The print profile is no longer public

It's very practical, however the overhangs on the sides were too large, which caused holes in the model, but apart from that everything works well 👍

Show original

@AlwaysFun

The print profile is no longer public

looks good, there is a bit of overhang issue around the bottom part.

@user_4127973846

Hi There, Printed the case and it printed extremely well and looks fantastic. Unfortunately it doesn't fit any of our 3 electric toothbrushes they are all Braun Oral B Pros. the case is just not deep enough and the lid wont slide over.

@user_3017969784

The print profile is no longer public

The size fits perfectly without any issues, but it might be better to orient it at 45 degrees and add supports

Show original

@frank_lab3D

The print profile is no longer public

Bed Adhesion Issue:Problems with adhesion and layer adhesion

Show original

@Zetof

Hello Zandor, Thank you for your design efforts and the new version. Yes, I'll print it again, but I don't see the version 2 file (OralB_TravelBox_EXT_v2.st). Only version 1 appears in the downloads (OralB_TravelBox_EXT.3mf)! One question: Do I have to print again just for the lid? Or both the lid and the box for version 2? Sincerely,

The designer has replied

@zandor973

Hello @Zetof , I see version V2 in the STL files (the first version has been removed) You may download only the 'OralB_TravelBox_EXT_v2.stl' file and print it alone No need to print the inner casing Do not use the .3mf file as it is based on the first version (this is a file uploaded by another user) Sincerely

Show original

@Zetof

Replying to @zandor973 :

Ok thanks for your information, I will restart the printing as soon as possible and I will post new photos here, thanks again!

@user_4089951001

Print Profile

No supports for the overhang and the latch to lock the design is too long, making it ineefetive after some use.

The profile uploader has replied

@tolip

what machine did you use to print?

@blaskovicz

overhang issues as others mentioned on the bottom of the insert. additionally the tab does not seem to stay engaged with the inner case, meaning it slides open unexpectedly. my work around for now is a rubber band around the top.